SIIG Computer Hardware PCI 2S User Manual

CyberPro PCI 2S  
Quick Installation Guide  
Introducing the CyberPro PCI 2S  
The CyberPro PCI 2S high-speed serial I/ O card provides  
two additional 9-pin serial ports.  
FeaturesandBenefits  
Conforms to PCI v2.2 Plug and Play  
Full support for Windows-based software  
Red u ces CPU load and im p roves system  
performance dramatically  
IRQ sharing feature reduces IRQ conflicts  
High-speed serial port (9-pin) works with 56K V.90  
external modems, ISDN terminal adapters, PDAs,  
digital cameras, label printers and other serial port  
devices  
Built-in FIFO buffers dramatically increase data  
transmit/ receive speed,especially under Windows'  
multitasking environment  
Each serial port can be configured for either 5V or  
12V output, for serial devices that require power  
SystemRequirements  
Pentium or equivalent computer with an available  
PCI slot  
Windows 95/ 98/ 98SE/ ME/ NT 4.0/ 2000/ XP/  
Server 2003  
04-0341B  
 
1
Hardware Installation  
General instructions for installing the card are provided  
below . Since the d esign of computer cases and  
motherboards vary, refer to your computers reference  
manual for further information, if needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computers case for a few  
seconds. Avoid any contact with internal parts and  
handle cards only by their external edges.  
1. Turn OFF the power to your computer and any  
other connected peripheral devices.  
2. Unplug the power cord from the back of the  
computer.  
3. Remove your computers cover.  
4. Remove the slot bracket from an available PCI slot.  
5. Change JP1 and JP2 jumper settings to the desired  
voltage only if your serial device needs additional  
power from the serial port. However, most serial  
devices do not require additional power. For more  
information see Figure 1 on page 2. Skip this step if  
power is not required.  
6. To install the card, carefully align the card's bus  
connector w ith the selected PCI slot on the  
motherboard. Push the board down firmly, but  
gently, until it is well seated.  
7. Replace the slot bracket's holding screw to secure  
the card.  
8. Replacethecomputer cover and reconnect thepower  
cord.  
3
 
Driver Installation  
This section provides information on how to install the  
CyberPro PCI 2S drivers.  
Windows95  
1. At the Update Device Driver Wizard, click Next.  
2. Insert the driver CD, and click Other Locations.  
Type in D:\ 9x, click OK, then Finish. (Change D: to  
match your CD-ROM drive letter)  
3. From the Insert Disk window, click OK. When the  
Cop yin g Files d ialog box ap p ears, typ e in  
D:\ 9x, then click OK.  
4. Restart Windows to complete the installation.  
Windows98/98SE  
1. At the Add New Hardware Wizard, click Next.  
2. Select Search for the best driver for your device  
(Recommend), then click Next.  
3. Insert the driver CD, check Specify a location,  
uncheck the other boxes, type in D:\ 9x, then click  
Next. (Change D: to match your CD-ROM drive  
letter)  
4.  
5.  
Click Next, then Finish.  
Repeat steps 1-4.  
6. Restart Windows to complete the installation.  
4
 
WindowsME  
1. At the Add New Hardware Wizard, select Specify  
the location of the driver (Advanced), click Next.  
2. Insert the driver CD, check Specify a location,  
uncheck the other box, type in D:\ Me, then click  
Next. (Change D: to match your CD-ROM drive  
letter)  
3.  
4.  
Click Next, then Finish.  
Repeat steps 1 and 2.  
5. Click Next, Next, then Finish.  
6. Restart Windows to complete the installation.  
ToVerifyWindows95/98/98SE/MEInstallation  
1. From the main desktop,double click My Computer,  
Control Panel,System,then click Device Manager.  
2. Double click Ports (COM & LPT), CyberSerial PCI  
16Cxxx... should be displayed two times.  
3. Double click M u lti-fu n ction ad ap ters, SIIG  
CyberPro 2S PCI board and PCI Function should  
be displayed.  
WindowsNT4.0  
1. From the desktop click Start, then Run.  
2. Insert  
the  
d river  
CD,  
typ e  
in  
D:\ NT4\ install_serial.exe,then click OK. (Change  
D: to match your CD-ROM drive letter)  
3. Click Next when the Welcome window appears.  
4. Choose Install, then click Next.  
5. Click Yes, then click Exit.  
6. Restart Windows to complete the installation.  
5
 
To Verify Windows NT 4.0 Installation  
1. Click Start, Settings, Control Panel, double click  
Ports device icon.  
2.  
Two new COM ports will be assigned when  
successfully installed.  
Windows2000  
1. At the Found New Hardware Wizard, click Next.  
2. Select Search for a suitable driver for my device  
(recommended), and click Next.  
3. Check Specify a location, uncheck the other boxes,  
and click Next.  
4. Insert the driver CD, type in D:\ 2000, then click OK.  
(Change D: to match your CD-ROM drive letter)  
5. Click Next and Finish.  
6. Repeat steps 1-5 two more times.  
7. Restart Windows to complete the installation.  
WindowsXP  
1. At the Found New Hardware Wizard, select Install  
from a list or specific location (Advanced), then  
click Next.  
2. Insert the driver CD, check Include this location in  
the search, uncheck the other check box, type in  
D:\ XP, and click Next. (Change D: to match your  
CD-ROM drive letter)  
3. If the Hardware Installation window pops up, click  
Continue Anyway, then Finish. Our driver has been  
testedfor stabilityandcompatibility.  
4. Repeat steps 1-3 three more times.  
5. Restart Windows to complete the installation.  
6
 
WindowsServer2003  
1. At the Found New Hardware Wizard,chooseInstall  
from a list or specific location (Advanced), then  
click Next.  
2. Insert the driver CD, check Include this location in  
the search, uncheck the other check box, type in  
D:\ 2003, and click Next. (Change D: to match your  
CD-ROM drive letter)  
3. IftheHardware Installation window,click Continue  
Anyway, then Finish. Our driver has been tested for  
stabilityandcompatibility.  
4. Repeat steps 1-3 three more times.  
5. Restart Windows to complete the installation.  
ToVerifyWindows2000/XP/Server2003  
Installation  
1. Right click My Computer, click Manage, then select  
Device Manager.  
2. Click on the + (plus sign) in front of Ports (COM &  
LPT), Cyb erSerial PCI 16Cxxx... shou ld be  
displayed two times.  
3. Dou ble click M u ltifu n ction ad ap ters, SIIG  
CyberPro 2S PCI board should be displayed.  
7
 
Changing COM Port Address  
Some serial devices need a specific COM port in order to  
work. If your serial device works properly, do not  
change this setting.  
Windows95/98/98SE/ME  
1. From the Device Manager window double click  
Ports (CO M & LPT), then d ouble click the  
CyberSerial PCI serial port you want to change.  
2. Click Settings tab, click the down arrow that is next  
to the Port Name box and select a COM address that  
is not currently in use.  
3. Click OK, then close Device Manager to save the  
changes.  
Windows2000/XP/Server2003  
1. From the Device Manager window double click  
Ports (CO M & LPT), then d ouble click the  
CyberSerial PCI serial port you want to change.  
2. Click Settings tab and click Advanced.  
3. Click the down arrow that is next to the COM Port  
number box and select a COM port that is not in use.  
Click OK.  
4. Click OK, then close Device Manager to save the  
changes.  
8
 
Technical Support and Warranty  
Q UESTIO N S?  
SIIG’s O n lin e Su p p ort has answ ers!  
Simply visit our website at www.siig.com and click on Support.  
Our online support database is updated daily with new drivers  
and solutions. Answers to your questions could be just a few clicks  
away. You can also submit questions online and one ofour technical  
support analysts will promptly respond.  
A lifetime manufacturer warranty supplied with this product is  
offered by SIIG, Inc. Please see SIIG website for more warranty  
details. If you should happen to encounter any problems with this  
product, please follow the procedures below.  
If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
If your purchase has passed the store's return policy period, please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective,an RMA number willbe issued. SIIG RMA department  
can also be reached at (510)413-5333.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost ofshipping the product to SIIG  
at the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538  
RMA #:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S and International Economy outside of the U.S at  
no cost to the customer.  
9
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading computer upgrade  
manufacturer of I/ O connectivity products, including PCI & ISA  
serial and parallel ports, USB, Serial ATA & UltraATA controllers,  
FireWire(1394a/ b),Networking,Sound Cards,and other accessories.  
SIIG is the premier one-stop source of upgrades.  
SIIGproductsoffer comprehensiveuser manuals,many user-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
found in computer retailstores,mailorder catalogs,and e-commerce  
sitesin theAmericasand theUK,aswellasthrough major distributors,  
system integrators, and VARs.  
PRODUCT NAME  
CyberPro PCI 2S  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause  
undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Ave.  
Fremont, CA 94538-3152  
CyberPro PCI 2S is a trademark of SIIG, Inc.  
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are  
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel  
Corporation. Other names used in publication are for identification only and may be trademarks  
oftheir respectivecompanies.  
March, 2005  
Copyright ©2005 by SIIG, Inc. All rights reserved.  
 

Sennheiser Microphone EW300IEMG3 User Manual
Sony Cordless Telephone SPP N1000 User Manual
Sony DVD Player Model DAV SR4W User Manual
Sony Home Theater System SSW EMD2 User Manual
Sony MiniDisc Player MDS SD1 User Manual
Sony Projector VPL CX20 User Manual
Soundstream Technologies Car Speaker EXC 10 User Manual
Southwestern Bell Car Speaker CM660 User Manual
StarTechcom Switch SV231U3A User Manual
Targus Camera Accessories TGRSD20 User Manual