SIIG Speaker 04 0600B User Manual

Satellite  
Speaker  
Mounts - 1 Pair  
Quick Installation Guide  
Introduction  
The Satellite Speaker Mounts - 1 Pair are fully-adjustable (Tilt,  
Swivel, & Pivot) speaker wall or ceiling mounts.  
KeyFeaturesandBenefits  
Universal design fits most speaker brands & designs  
Ceiling or wall mountable & compatible with 1, 2, or  
4-holeandkey-holespeakermounting(withincluded  
adapters)  
Allows customizable tilt, swivel, & pivot angle  
adjustments for optimal speaker positioning  
Holds speakers weighing up to 8 lbs  
Serial Number Sticker  
For future product return or exchange, this serial number is  
required. Please keep it for your reference.  
04-0600B  
1
 
Installation  
Pleasereadtheinstructionspriortoinstallation. Thisspeaker  
mount is designed solely for the mounting of small speakers  
weighing less than 8lbs. We are not responsible for damage  
that may occur if speakers weighing more than 8lbs. are  
used.  
The user will have to determine which type of configuration  
will work best with the included mounting hardware. If the  
included hardware does not fit with the application, the  
appropriate hardware will have to be purchased.  
Single Hole Mounting  
1.  
Most satellite speakers will require the use of the  
M5 x 20mm machine screw used in combination with  
M5x1/8"plasticwasher.Theplasticwasherisusedas  
a spacer between the threaded insert and the post, see  
Figure 1 below. It is critical the plastic washer is used  
correctly.  
M5 x 20mm  
Machine Screw  
Back Speaker  
Mounting Post  
M5 x 1/8"  
Plastic Washer  
Figure 1  
3
 
2.  
3.  
Once the proper configuration is determined, secure  
the post to the speaker.  
Some speakers use the smaller M4 x 8 screw, which is  
inserted into the off-center on the mounting post, see  
Figure 2 below.  
M4 x 8mm Flat Head  
Machine Screw  
Back Speaker  
Figure 2  
4.  
Check the size of the hole, make sure you have the  
8-32x5/8"machinescrew,the1/4"-20x1/2"machine  
screw, the M6 x 20mm, or the M5 x 20mm fits inside,  
see Figure 3 below.  
M5 x 1/8" Plastic Washer  
Back Speaker  
8-32 x 5/8" Machine Screw  
1/4"-20 x 1/2" Machine Screw  
Figure 3  
 
4
5.  
When the correct size is determined, place the screw  
through the speaker post and attach to the rear of the  
speaker enclosure. If the screw does not tighten  
properly, use the M5 x 1/8" plastic washer to tighten  
it up.  
Key Hole Mounting  
1.  
If your speaker has a factory key hole design, you will  
use the 8-32 x 5/8" machine screws in combination  
with the 8-32 Hex Key Hole Nut.  
2.  
Loosely pre-assemble the mounting post with the  
8-32 x 5/8" machine screw and hex key hole nut, see  
Figure 4 below.  
Mounting Post  
Keyhole  
M5 x 1/8"  
Plastic Washer  
8-32 x 5/8"  
Back Speaker  
Machine Screw  
8-32 Hex Key Hole Nut  
Figure 4  
5
 
3.  
4.  
Engage the hex key hole nut into the key hole slot.  
Put tension on the assembly by gently pulling back on  
the speaker mount post while tightening the  
8-32 x 5/8" machine screw, see Figure 4 on page 5.  
5.  
6.  
Thehexkeyholenutwillengageonthehousinginthe  
key hole slot.  
If the post does not tighten securely against the  
housing, it will be necessarry to use the M5 x 1/8"  
plastic washer as a spacer under the head of the  
8-32 x 5/8" machine screw, see Figure 4 on page 5.  
2/4 Hole Mounting  
1.  
Find the best mounting configuration that matches  
your speaker enclosure. Four-hole mount patterns  
can be accomodated by positioning the speaker plate  
diagonally, see Figure 5 on the next page.  
2.  
Using the 1/4"-20 x 1/2" machine screws, install the  
speaker plate and secure the speaker enclosure, see  
Figure 5 on the next page.  
6
 
Back  
1/4"-20 x 1/2"  
Machine Screw  
Speaker  
4-Hole  
Orientation  
2-Hole Orientation  
Figure 5  
Self-TappedMounting  
1.  
Locate the optimum location for the mounting plate  
and use it as template to mark the drilling locations.  
Donotdrillorscrewintothespeakerwhereyoucould  
possibly damage the internal components.  
2.  
Drillthepilothole(s)usinga1/8"drillbit.Theholes(s)  
shouldnotbedrilledmorethan1/2"depth,seeFigure  
6 on the next page.  
7
 
#12 x 3/4" Self  
Tapping Screw  
Back Speaker  
Figure 6  
Mounting to the Wall or Ceiling  
The mounting hardware for the three different surface  
applications is supplied. You will need to determine what  
style hardware will work best with your mounting surface.  
Alwaysusecautionwhendrillingintoawallorceiling. Make  
sure to avoid all electrical and water lines.  
WoodSurface  
1.  
Using a stud finder, locate the wood stud or framing  
member. Always mount the speakers in the center of  
a stud.  
2.  
Usingthewallplateasatemplate,markholepositions  
onmountingsurface. Forin-wallapplications,position  
the mounting holes in a vertical pattern, see Figure 7  
on the next page.  
8
 
#12 x 1 3/4" Self  
Tapping Screw  
Figure 7  
3.  
4.  
Drill holes through the drywall and into the wood  
studusinga1/8"drillbit. Theseholesshouldbedrilled  
1 1/2" deep, see Figure 7 above.  
After the holes are drilled, mount the wall plate using  
the self tapping screws.  
DrywallSurfaces  
1.  
Locate the best mounting location in the ceiling or  
wall. Usingthewallplateasatemplate, markthehole  
positions on the mounting surface. For in-wall  
applications,positionthemountingholesinavertical  
pattern, see Figure 8 on the next page.  
2.  
3.  
Drill holes in the drywall using a 5/16" drill bit.  
Once the holes are drilled, insert the alligator anchor  
into the holes. Make sure the anchor is flush with the  
wall and/or ceiling surface, see Figure 8 on the next  
page.  
9
 
4.  
Withtheanchorsinplace, mountthewallplatesusing  
the #12 x 3/4" self tapping screws, see Figure 8 below.  
#12 x 3/4" Self  
Pre Drill 5/16"  
Holes  
Tapping Screw  
Insert screw through wall plate  
and into the alligator anchor  
Insert Alligator  
Anchor  
Figure 8  
ConcreteSurface  
1.  
Usingthewallplateasatemplate,markholepositions  
on the mounting surface. For in-wall applications,  
position the mounting holes in a vertical pattern, see  
Figure 9 on the next page.  
2.  
Drill holes in the solid concrete or hollow block using  
a 5/16" masonry bit. Once the holes are drilled, insert  
the # 12-14 alligator anchors into the holes and make  
suretheanchorisflushwiththesurfaceofthewall,see  
Figure 9 on the next page.  
10  
 
Insert Alligator  
Anchor  
#12 x 3/4" Self  
Tapping Screw  
Insert screw through wall plate  
and into the alligator anchor  
Using the hammer to  
tap anchor into place  
Figure 9  
3.  
With the wall anchor in place, mount the wall plate  
using the #12 x 3/4" self tapping screws, see Figure 9  
above.  
ExtensionMounting  
This is for ceiling and/or shelf applications. Do not use  
extension in the wall application.  
1.  
Install a 2 1/4" ceiling mount extension to the wall  
plate.  
2.  
Securethesetscrewtoholdtheextensioninplacewith  
the weight of the speaker attached.  
Tighten the allen screw using  
the provided allen wrench  
Figure 10  
11  
 
Low-ProfileMounting  
This is for wall and ceiling application.  
1.  
Installthelow-profileportionofthespeakermountto  
the wall plate or 2 1/4" extension.  
2.  
Securethesetscrewtoholdtheextensioninplacewith  
the weight of the speaker attached.  
Tighten the allen screw using  
the provided allen wrench.  
Figure 11  
SpeakerMounting  
1.  
Install the speaker with the speaker post or 2-hole  
plate attached.  
2.  
Securethescrewtoholdtheextensioninplacewiththe  
weight of the speaker attached.  
Post Style Speaker  
2-Hole Speaker  
Figure 12  
 
12  
Blank Page  
13  
 
Blank Page  
14  
 
TechnicalSupportandWarranty  
QUESTIONS? SIIGs Online Support has answers! Simply visit our web site at  
www.siig.com and click Support. Our online support database is updated daily with  
new drivers and solutions. Answers to your questions could be just a few clicks away.  
You can also submit questions online and a technical support analyst will promptly  
respond.  
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the  
original purchaser and guarantees the product to be free of any defects in materials or  
workmanship for five (5) years from the date of purchase of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product  
having similar features and functionality) the product if defective in materials or  
workmanship. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store  
where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow the steps  
below to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Goto www.siig.com, clickSupport,then REQUESTAPRODUCTREPLACEMENT  
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request  
will be processed, if the product is determined to be defective, an RMA number will  
be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All accessories that came with the  
original package must be included.  
Clearly write your RMA number on the top of the returned package. SIIG will  
refuse to accept any shipping package, and will not be responsible for a product  
returned without an RMA number posted on the outside of the shipping  
carton.  
You are responsible for the cost of shipping to SIIG. Ship the product to the  
followingaddress:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #:  
SIIG will ship the repaired or replaced product via Ground in the U.S. and  
International Economy outside of the U.S. at no cost to the customer.  
15  
 
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingmanufacturerofITconnectivitysolutions  
(including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy  
I/Oadapters)thatbridgetheconnectionbetweenDesktop/Notebooksystems  
and external peripherals. SIIG continues to grow by adding A/V and Digital  
Signageconnectivitysolutionstoourextensiveportfolio.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendlyfeatures,  
andarebackedbyanextensivemanufacturerwarranty. Highqualitycontrol  
standards are evident by the overall ease of installation and compatibility of  
ourproducts,aswellasoneofthelowestdefectivereturnratesintheindustry.  
SIIG products can be found in computer retail stores, mail order catalogs,  
throughmajordistributors,systemintegrators,andVARsintheAmericasand  
theUK,andthroughe-commercesites.  
PRODUCT NAME  
Satellite Speaker Mounts - 1 Pair  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
Satellite Speaker Mounts - 1 Pair is a trademark of SIIG, Inc. SIIG and the SIIG logo are  
registeredtrademarksofSIIG,Inc. Allothernamesusedinthispublicationareforidentification  
only and may be trademarks of their respective owners.  
November, 2011  
Copyright © 2011 by SIIG, Inc. All rights reserved.  
 

Shark Vacuum Cleaner NV355 User Manual
SonicWALL Network Router EM5000 User Manual
Sony Car Stereo System CDX GT615UV User Manual
Sony Personal Computer PCV RS710 User Manual
Sony Speaker CMT ED2U User Manual
Sony Stereo Receiver 3 289 204 411 User Manual
StarTechcom Video Gaming Accessories ST121SHD50 User Manual
Sunbeam Toaster TA6450 User Manual
Symbol Technologies PDAs Smartphones AccuScan Palm Pro User Manual
Tanita Stereo System PD640 User Manual