Sennheiser Microphone E825S User Manual

825  
S
Bedienungsanleitung  
Instructions for use  
Notice d‘emploi  
Istruzioni per l‘uso  
Instrucciones para el uso  
Gebruiksaanwijzing  
 
Delivery includes  
y
y
y
y
y
825 S microphone  
MZQ 800 microphone clamp  
Pouch  
Instructions for use  
Warranty Certificate  
ON/OFF switch  
Use the screw to lock the switch in the ON position. With  
the switch set in the ON position, gently turn the screw  
head 90° to lock the switch in position.  
Removing the sound inlet basket  
2
 
Positioning the microphone  
Position  
Resulting sound  
Commentary  
High proximity effect  
(much bass/  
fundamental)  
Very little crosstalk  
from other sound  
sources  
powerful, direct sound  
Less proximity effect  
(less bass/  
More crosstalk from  
other sound sources  
fundamental)  
Some room ambience,  
natural, balanced sound  
Very little proximity  
effect (little bass/  
fundamental)  
Much crosstalk from  
other sound sources  
More room ambience,  
indirect sound  
If sibilance or „popping“ occurs, position the microphone  
not directly in front of the mouth but slightly to the side.  
In order to prevent feedback, position monitor  
loudspeakers so that they are located in the angle area of  
the highest cancellation of the microphone.  
In order to prevent interference due to crosstalk between  
adjacent sound sources, try to position the microphone so  
that the interfering sound source is located in the angle  
area of the highest cancellation of the microphone  
(approx. 180°; see polar diagram).  
3
 
Polar diagram  
0°  
0
30°  
30°  
5
10  
15  
20  
25  
dB  
60°  
60°  
90°  
90°  
120°  
120°  
150°  
150°  
180°  
2000 Hz  
4000 Hz  
8000 Hz  
16000 Hz  
125 Hz  
250 Hz  
500 Hz  
1000 Hz  
Frequency response curve  
dBv  
- 40  
- 50  
- 60  
- 70  
- 80  
- 90  
20  
50  
100 200  
500 1000 2000 5000 10000 20000 Hz  
0°, 1 m  
4
 
Specifications  
Transducer principle  
Frequency response  
Pick-up pattern  
dynamic  
80.....15,000 Hz  
cardioid  
Sensitivity  
(free field, no load at 1 kHz)  
1.5 mV/Pa  
350 Ω  
1 kΩ  
Nominal impedance  
Min. terminating impedance  
Connector  
XLR-3  
Operating temperature  
Weight  
0°C to +40°C  
330 g  
Dimensions  
Ø 48 x L 180 mm  
Pin assignment of XLR-3 connector  
+
+
+
+
1
2
2
1
2
1
3
3
3
XLR  
XLR  
XLR  
+
1
2
3
+
+
6,3 mm  
6,3 mm  
XLR  
+
1
2
3
XLR  
balanced  
5
 
Overview of microphone applications  
Variant  
Application  
Vocals  
Choirs  
x
x
x
x
x
x
x
x
Studio,  
acoustic instruments  
Orchestra  
x
Brass / Saxophone  
Acoustic guitar  
Acoustic bass  
Guitar amplifiers  
Bass amplifiers  
Leslie  
x
x
x
x
x
x
x
x
x
x
Piano, grand piano  
Kick drums  
x
x
x
Snare drums  
Rack toms  
x
x
x
x
x
x
x
x
x
x
Floor toms  
Congas  
x
x
Cymbals  
x
x
x
Percussion  
x
x
Overheads  
6
 
Manufacturer declarations  
Warranty  
2 years  
Approval  
Sennheiser electronic GmbH & Co. KG declare that  
this device is in compliance with the applicable CE  
standards and regulations.  
Before putting the device into operation, please observe the respec-  
tive country-specific regulations!  
WEEE Declaration  
Please dispose of this product at the end of its operati-  
onal lifetime by bringing it to your local collection point  
or recycling centre for such equipment.  
7
 
Sennheiser electronic GmbH & Co. KG  
30900 Wedemark, Germany  
Phone +49 (5130) 600 0  
Fax +49 (5130) 600 300  
Printed in Germany  
Publ. 07/06  
511654/A02  
 

Sharp Calculator EL 1750PIII User Manual
Sharp Calculator EL9900 User Manual
Sharp Cash Register XE A213 User Manual
Sony Bicycle Accessories VCT HM1 User Manual
Sony Car Stereo System XVM R70 User Manual
Sony Laptop VPCW222AX WI User Manual
Sound Performance Lab DJ Equipment Parametric Equalizer User Manual
Southwestern Bell Telephone FT365 User Manual
SUPER MICRO Computer Computer Hardware X8DTU LN4F+ User Manual
Tanaka Water Pump TCP 25 User Manual