Shark Carpet Cleaner S3505W User Manual

WWW.SHARKCLEAN.COM  
Steam Pocket® Mop  
S3505W  
OWNER’S GUIDE  
 
English  
11. DO NOT unplug by pulling on  
power cord. To unplug, grasp the  
plug not the power cord. Do not  
use extension cords or outlets  
with inadequate current carrying  
capacity.  
22. Extreme caution should be  
exercised when using this  
appliance to clean stairs.  
23. Never use steam mop without  
micro-fiber pocket attached.  
24. Keep your work area well lit.  
12. DO NOT put any objects into  
openings. Do not use with any  
opening blocked.  
25. Store steam mop indoors in a cool,  
dry place.  
13. DO NOT put hands or feet under  
26. To avoid circuit overload, do not  
operate another appliance on the  
same socket (circuit) as the steam  
cleaner.  
the steam mop. Unit gets very hot.  
14. Use ONLY on flat, horizontal  
surfaces. Do not use on walls,  
counters or windows.  
27. If an extension cord is absolutely  
necessary, an extension cord rated  
a minimum of 15 ampere, 14 gage  
cord should be used. Cords rated  
for less amperage may overheat.  
Care should be taken to arrange  
cord so that it cannot be pulled or  
tripped over.  
15. DO NOT use on leather, wax  
polished furniture or floors,  
synthetic fabrics, velvet or other  
delicate, steam sensitive materials.  
16. DO NOT add cleaning solutions,  
scented perfumes, oils or any other  
chemicals to the water used in this  
appliance as this may damage the  
unit or make it unsafe for use. If  
you live in a hard water area, we  
recommend using distilled water in  
your steam mop.  
28. DO NOT leave your Steam Pocket®  
Mop unattended when the system  
is connected to a power supply  
or electrical outlet.  
29. DO NOT store unit with damp or  
wet micro-fiber cleaning pocket  
attached. Never leave the steam  
mop in one spot on any surface for  
any period of time with a damp or  
wet micro-fiber cleaning pocket  
attached as this will damage  
your floors.  
17. When in use, NEVER turn the  
appliance over or on its side.  
NEVER DIRECT STEAM TOWARDS  
PEOPLE, ANIMALS OR PLANTS.  
18. NEVER LEAVE THE STEAM  
POCKET® MOP IN ONE SPOT ON  
ANY SURFACE FOR ANY PERIOD  
OF TIME WHEN MICRO-FIBER  
POCKET IS ATTACHED.  
30 Always unplug and allow the steam  
mop to cool before removing or  
changing mop heads.  
19. Carefully remove the micro-fiber  
pocket immediately after you have  
unplugged and allowed the steam  
mop to cool.  
WARNING: Your steam mop  
is designed to clean hard floor  
surfaces that will withstand high  
heat. Do not use on unsealed wood  
or unglazed ceramic floors. On  
surfaces that have been treated  
with wax or some no wax floors,  
the sheen may be removed by the  
heat and steam action. It is always  
recommended to test an isolated  
area of the surface to be cleaned  
before proceeding. We also  
20. When cleaning the steam mop,  
unplug the power cord from the  
electrical outlet and clean with a  
dry or damp cloth. Do not pour  
water or use alcohol, benzene or  
paint thinner on the unit.  
21 To reduce the risk of fire, DO NOT  
use a flammable or combustible  
liquid to clean a floor.  
recommend that you check the use  
and care instructions from the floor  
manufacturer.  
 
Quick Start  
When assembling your steam mop  
there may be a little water in or around  
the water tank. This is because we test  
all our steam mops 100% before you  
buy them, so you get a quality  
Shark® Steam Pocket® Mop.  
1
3
2
4
ASSEMBLE  
1
Insert the mop handle into the  
pump actuator (the tube that leads  
to the tank). Push the mop handle  
and pump actuator together until  
you hear them click into place.  
FILL  
4
Lay the mop on the floor or on  
a counter top and remove the  
water tank cap by turning counter  
clockwise. Fill the water tank using  
the filling flask. Do not overfill the  
water tank. Replace the water cap  
and tighten.  
2
Select a mop head. Choose the  
All-Purpose, Versa-Tile™ or Large  
Area mop head. Fit one side of  
the pocket onto the head first,  
then using the lavender loop, pull  
the Steam Pocket® over the head.  
Attach the quick fasteners on the  
top of the pocket to secure in place.  
IMPORTANT: Make sure your floors  
are sealed. Before using the Steam  
Pocket® Mop consult page 3 for  
more information.  
3
Snap the mop head into the base to  
secure it. Press the release button  
to exchange mop heads.  
TOLL FREE: 1-800-798-7398  
 
DIRT CAN’T HIDE ON  
EITHER SIDE! When one  
side of the pocket gets  
dirty, just turn the mop  
head over and clean with  
the other side of the  
Steam Pocket®.  
5
QUICK TIP:  
For easier  
pushing  
and pulling,  
extend the  
handle length.  
6
QUICK TIPS: Your Steam  
Pocket® Mop comes with 3  
unique mop heads. Use the  
All-Purpose mop head for  
any room in your house, the  
PREPARE  
5
For your comfort, you can adjust  
the height of the mop. Just lift the  
latch on the tube 90 degrees to the  
open position. Holding the handle,  
extend the tube to the height that  
is right for you and then close latch  
to locked position.  
triangular Versa-Tile mop  
head for bathrooms and  
tight spaces and the Large  
Area mop head for wide  
area cleaning.  
NOTE: Do not leave your  
Steam Pocket® Mop  
6
Plug in mop and wait 30 seconds  
or less for the mop to heat up.  
Pump the handle of the mop by  
pushing downward about 10 to 12  
times to create steam.  
unattended during use.  
IMPORTANT: Never leave  
the Steam Pocket® Mop in  
one spot for any period of  
time with a damp or wet  
micro-fiber Steam Pocket®  
attached as this will damage  
your floors.  
NOTE: Steam is created  
automatically when you start  
mopping.  
 
TECHNICAL SPECIFICATIONS  
Voltage:  
Power:  
Water  
120V., 60Hz.  
1550 Watts  
Capacity: 450 ml (15 oz.)  
TOLL FREE: 1-800-798-7398  
 
English  
Contents  
Getting Started......................................................................2  
Using Your Steam Mop .......................................................6  
Using Your Carpet Glider ...................................................8  
Care of Your Steam Mop....................................................9  
Troubleshooting Guide .......................................................11  
Notes..........................................................................................12  
Thank you for  
purchasing the  
Shark® Steam  
Pocket® Mop.  
1
 
Getting Started  
i
j
When assembling your steam mop there  
may be a little water in or around the  
water tank. This is because we test all  
our steam mops 100% before you buy  
them, so you get a quality Shark®  
Steam Pocket® Mop.  
k
a
l
b
d
n
o
c
m
e
f
p
h
g
a Two-Sided Micro-Fiber Steam Pocket®  
i
j
Mop Handle  
Quick Release Swivel Cord Wrap  
for the Large Area Mop Head (1)  
b Two-Sided Micro-Fiber Steam Pocket®  
k Cord Clips  
Telescopic Handle Latch  
for the All-Purpose Mop Head (1)  
l
c Two-Sided Duster Steam Pocket® for  
m Water Tank Viewing Window  
the All-Purpose Mop Head (1)  
n Power-On Blue Light  
(Lights up when plugged-in)  
d Two-Sided Micro-Fiber Steam Pocket®  
for the Versa-Tile™ Mop Head (1)  
o Water Tank Cap  
e Carpet Glider  
p Large Area Mop Head  
f
Filling Flask  
g Versa-Tile™ Mop Head  
h All-Purpose Mop Head  
2
TOLL FREE: 1-800-798-7398  
 
English  
1
2
ASSEMBLE  
IMPORTANT: Always make sure the  
mop is UNPLUGGED from the wall  
when not in use. Never fill the mop,  
attach the mop head, change or  
remove the micro-fiber pocket when  
the mop is plugged into the wall. If  
you have hard water you might want  
to use distilled water to prolong the  
life of the Shark® Steam Pocket®  
Mop. Make sure you only add water  
to the tank. Chemicals or cleaning  
solutions may damage the appliance  
and could be unsafe for you and your  
family.  
1
Insert the mop handle into the pump  
actuator (the tube that leads to the  
tank). Push the mop handle and  
pump actuator together in until you  
hear them click into place.  
2
Select a mop head. All of the mop  
heads can be used on your floors,  
but the Versa-Tile bathroom head is  
particularly useful for tight corners  
and the Large Area mop head is  
great for big jobs.  
Use the lavender loop on the side of  
the micro-fiber cleaning pocket to  
place it around the mop head. Then  
attach the quick fasteners on the  
top of the pocket to secure in place.  
You can also use the loop to pull the  
dirty pocket off when you are done  
mopping and it  
has cooled.  
3
 
Getting Started  
4
3
3
Snap the mop head into the base to  
secure it. Press the release button to  
exchange mop heads.  
IMPORTANT: Do not use on unsealed  
wood or unglazed ceramic floors.  
On surfaces that have been treated  
with wax, the sheen may be removed  
by the heat and steam action. It is  
always recommended to test an  
isolated area of the surface to be  
cleaned before proceeding. We  
recommend that you check the use  
and care instructions from the floor  
manufacturer.  
4
Turn the water tank cap counter  
clockwise and remove from the tank.  
Use the filling flask and pour water  
into the tank. Do not overfill. Replace  
the cap on the water tank by turning  
clockwise and tightening.  
4
TOLL FREE: 1-800-798-7398  
 
English  
5
5
For your comfort, you can adjust  
the height of the mop. Just lift the  
latch on the tube 90 degrees to the  
open position. Holding the handle,  
extend the tube to the height that is  
comfortable for you and then lower  
the latch to locked position.  
QUICK TIP: For easier pushing and  
pulling, extend the handle length.  
5
 
Using Your Steam Pocket® Mop  
IMPORTANT: Do not use the mop  
without first attaching a micro-fiber  
pocket and adding water to the tank  
first. When you are using the mop  
for the first time, it might take longer  
than the normal 30 seconds to start  
steaming. Just pump the handle a  
few times in a downward motion to  
prime the pump and it should be  
ready.  
2
1
NOTE: Make sure the floors are  
swept or vacuumed before using the  
steam mop.  
2
Pump the handle a few times in a  
downward motion. This pumping  
action will release steam as you  
mop and allows you to customize  
the amount of steam you want.  
Begin mopping with a forward  
and backward motion. The natural  
motion of mopping will produce  
steam.  
1
Pull and twist the quick release cord  
holder to unwrap the power cord  
completely.  
Plug into a 120-volt electrical outlet  
The power “On” light will turn blue. It  
takes approximately 30 seconds for  
the mop to heat up and for the steam  
to be ready.  
6
TOLL FREE: 1-800-798-7398  
 
English  
3
3
When one side of the micro-fiber  
Steam Pocket® gets dirty, just flip the  
mop head and you can quickly start  
using the other side. Dirt cannot hide  
on either side.  
4 When the water tank is empty, the  
steam mop will stop producing  
steam. You can refill the water tank  
at any time as long as the mop is  
unplugged from the outlet. Follow  
the instructions from page 3.  
IMPORTANT: Please wait 3-5 minutes  
for the Steam Pocket® Mop to cool  
off before switching the mop head or  
the micro-fiber Steam Pocket®.  
IMPORTANT: Never leave the  
Steam Pocket® mop with a damp or  
wet micro-fiber Steam Pocket® on  
any floor surface for any amount of  
time. This may damage the floor.  
7
 
Using Your Carpet Glider  
The Steam Pocket® Mop will  
not clean your carpeting  
or area rugs. However, it is  
great for deodorizing and  
freshening.  
1
THE CARPET GLIDER  
1 The Carpet Glider can be used with  
the All-Purpose Mop Head to lightly  
steam your carpet and area rugs.  
Just place the mop head on top of  
the glider and move back and forth  
across a section of the carpet. The  
Steam Pocket® mop will not clean  
your carpeting or areas rugs, but it is  
great for deodorizing and freshening.  
NOTE: Please note that the Steam  
Pocket® Mop rests on top of the  
carpet glider and it is not a fixed  
attachment. Do not leave steam mop  
with carpet glider in one stationary  
position for any period of time.  
8
TOLL FREE: 1-800-798-7398  
 
English  
Care of Your Steam Pocket® Mop  
AFTER USE AND STORAGE  
1
When you have finished using the  
Steam Pocket® Mop, unplug the cord  
from the outlet and move it into an  
upright position. Let the unit cool  
3-5 minutes and release steam by  
pumping the handle several times  
before removing the micro-fiber  
Steam Pocket® from the mop head.  
3
1
2
2 Remove the micro-fiber Steam  
Pocket® by releasing the quick  
fasteners and using the lavender  
loop on the side of the pocket,  
avoiding contact with the hot pocket  
or dirt. Then empty the water tank.  
3
To store the Shark® Steam Pocket®  
Mop, first remove the head (after it  
has cooled and the steam has been  
released) then hang on a large hook.  
NOTE: If you want to store Steam  
Pocket® Mop standing upright, make  
sure it is leaning against a wall for  
added support and safety. Always  
store your Steam Pocket® Mop  
with the micro-fiber Steam Pocket®  
removed. Store away from children  
and high traffic areas.  
IMPORTANT: Steam Pocket® may be  
very hot from the steam. Use caution  
when removing. Let the unit cool  
3-5 minutes.  
9
 
Care of Your Steam Pocket® Mop  
2
1
CLEANING YOUR MICRO-FIBER  
STEAM POCKET®  
2
If there are loose threads on the  
Steam Pocket® , carefully cut the  
thread with scissors. Do not pull on  
them or cut at the base.  
1
We recommend washing your micro-  
fiber Steam Pocket® separately from  
other fabrics to avoid picking up lint.  
Only use liquid detergent (no powder  
detergent). Do not use any fabric  
softeners or bleach.  
Line dry or dry on a low dryer  
setting.  
10  
TOLL FREE: 1-800-798-7398  
 
English  
Troubleshooting Guide  
PROBLEM  
POSSIBLE REASONS & SOLUTIONS  
Your Steam Pocket® Mop should be securely plugged  
into a 120V AC electrical outlet only.  
Steam Pocket® Mop  
will not turn on.  
Check your fuse or breaker.  
Steam Pocket® Mop  
will not make steam.  
Prime the pump, see page 6 for more information.  
Is there water in the water tank? If not, add water to  
your Steam Pocket® Mop following the instructions.  
Check to see if your micro-fiber Steam Pocket® is too  
wet. We recommend you unplug the Steam Pocket®  
Mop and change the micro-fiber Steam Pocket®.  
Steam Pocket® Mop  
leaves water on the  
floor.  
Make sure the Steam Pocket® is attached correctly.  
Make sure the Steam Pocket® is attached correctly.  
Steam Pocket® Mop  
is hard to push.  
Check to see if your Steam Pocket® is excessively dirty.  
Try increasing the height of the pole for better leverage.  
The micro-fiber Steam Pocket® might be dirty. Flip or  
change the pocket.  
If you washed the Steam Pocket® with powder, leftover  
detergent may be causing the streaks. Re-wash pocket  
with liquid detergent.  
Floors are cloudy,  
streaky or spotty  
after steaming.  
If you are cleaning in a kitchen area where there might  
be a build-up of grease, clean the area first with a  
degreasing agent such as an all-purpose cleaner or dish  
soap and paper towels.  
You might have left the mop in the same spot for  
too long.  
Do you have hard water? If you do, we recommend  
using distilled water.  
11  
 
Notes  
12  
TOLL FREE: 1-800-798-7398  
 
English  
ONE (1) YEAR LIMITED WARRANTY  
EURO-PRO Operating LLC warrants this product to be free from defects in material and  
workmanship for a period of one (1) year from the date of the original purchase, when utilized for  
normal household use, subject to the following conditions, exclusions and exceptions.  
If your appliance fails to operate properly while in use under normal household conditions  
within the warranty period, return the complete appliance and accessories, freight prepaid. For  
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC  
will repair or replace it free of charge. Proof of purchase date and $9.95 to cover the cost of  
return shipping and handling must be included. *  
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or  
replacement of the unit at our option. This warranty does not cover normal wear of parts and  
does not apply to any unit that has been tampered with or used for commercial purposes. This  
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage  
due to faulty packaging or mishandling in transit. This warranty does not cover damage or  
defects caused by or resulting from damages from shipping or repairs, service or alterations to  
the product or any of its parts, which have been performed by a repair person not authorized by  
EURO-PRO Operating LLC.  
This warranty is extended to the original purchaser of the unit and excludes all other legal and/  
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,  
is limited to the specific obligations expressly assumed by it under the terms of the limited  
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential  
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or  
limitation of incidental or consequential damages, so the above may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state or province to province.  
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of  
purchase date and to attach tag to item before packing with your name, complete address and  
phone number with a note giving purchase information, model number and what you believe  
is the problem with the item. We recommend you insure the package (as damage in shipping  
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER  
SERVICE”. We are constantly striving to improve our products, therefore the specifications  
contained herein are subject to change without notice.  
OWNERSHIP REGISTRATION CARD FOR  
CANADIAN CONSUMERS ONLY  
Please complete and return within ten (10) days of purchase. The registration will enable  
us to contact you in the event a product defect is discovered. By returning this card you  
acknowledge to have read and understood the instructions for use, and warnings set  
forth in the accompanying instructions.  
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7  
PURCHASER: ……………………………………………………………………………………………............  
ADDRESS: ………………………………………………………………………………………………...............  
S3505W  
DATE OF PURCHASE: …………………….. MODEL: ………………...................................  
NAME AND ADDRESS OF STORE: …………………………………………………………………..  
13  
 
U.S.:  
EURO-PRO Operating LLC  
180 Wells Ave  
Newton, MA 02459  
Canada: EURO-PRO Operating LLC  
4400 Bois Franc  
Ville St. Laurent, Québec H4S 1A7  
1-800-798-7398  
Sharkclean.com  
COPYRIGHT© EURO-PRO OPERATING LLC 2010  
PRINTED IN CHINA  
REV. 100428  
Illustrations may differ with actual product.  
 

Shure Microphone 27E3027 User Manual
Snapper Lawn Aerator 4562 User Manual
Sony Cordless Telephone SPP ID970 User Manual
Sony DVD Player DVP SR400P User Manual
Sony VCR SLV SX10EG User Manual
Sunfire Stereo System TGP 5E User Manual
SUPER MICRO Computer Computer Hardware R1K62BP User Manual
Sylvania CRT Television 6427TE User Manual
Sylvania Portable DVD Player SDVD8728 User Manual
Symantec Patio Umbrella 10024709 User Manual