Sharp Microwave Oven Inside Pro User Manual

Microwave Drawer  
INSTALLATION MANUAL  
SPECIAL WARNING  
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.  
IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL  
INSPECTOR’S USE.  
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
CLEARANCES AND DIMENSIONS  
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in  
accord with the stated clearances and dimensions on pages 2 and 3. See Figures 1 and 2.  
UNPACKING YOUR MICROWAVE DRAWER  
IMPORTANT NOTES  
2
2
2
2
3
3
ELECTRICAL OUTLET  
4
4
4
4
4
GROUNDING INSTRUCTIONS  
DRAWER INSTALLATION  
IMPORTANT SAFETY INSTRUCTIONS  
CLEARANCES AND DIMENSIONS  
MICROWAVE DRAWER MEASUREMENTS  
ANTI-TIP BLOCK  
MODEL AND SERIAL NUMBER LOCATION  
CARE, CLEANING AND MAINTENANCE  
 
INSTALLATION MANUAL  
electrical outlet  
location  
6"  
2x4 Anti-  
Tip block  
MICROWAVE DRAWER MEASUREMENTS  
3 1/2"  
5"  
4"  
14 3/4"  
to bottom  
28 7/16"  
opening  
allow 1/4"  
of Anti-Tip  
overlap  
allow 3/4"  
overlap  
block  
14 3/4"  
opening  
23 1/2"  
min depth  
allow 3/4"  
overlap  
36"  
countertop  
height  
floor must  
support  
100 lbs.  
allow 7/16"  
overlap  
84"  
wall  
cabinet  
19"  
to top of floor  
optional wall oven  
cutout illustrated  
in sketch  
NOTE: Open Top  
Cabinet illustrated  
30" *  
cabinet min.  
electrical outlet  
location  
(6")  
Figure 1  
2x4 Anti-Tip block  
3 1/2"  
5"  
Figures 1 and 2 contain many Microwave Drawer measurements  
for reference when planning the drawerʼs location.  
2" minimum  
4"  
28 7/16"  
opening  
14 3/4"  
to bottom  
of Anti-Tip  
block  
4 11/16"  
28 1/8"  
allow 1/4"  
overlap  
allow 3/4"  
overlap  
2"  
14 3/4"  
opening  
23 1/2"  
allow 3/4"  
overlap  
min depth  
floor must  
support 100 lbs.  
allow 7/16"  
overlap  
15 13/32"  
14 19/32"  
15"  
auto drawer  
opening  
*19"  
to top of floor  
(recommended)  
23 3/8"  
30"  
cabinet min.  
Figure 2  
Figure 3  
1 13/16"  
door thickness  
30"  
NORMAL INSTALLATION STEPS  
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS  
ANTI-TIP BLOCK  
To reduce the risk of tipping of the drawer, the Anti-Tip block  
must be properly installed located 14 3/4-inches above the floor on  
which the Microwave Drawer will sit. The 6-inch 2 x 4 Anti-Tip  
block must be provided by the installer. See Figures 1, 2 and 4.  
The Anti-Tip block prevents serious injury that might result from  
spilled hot liquids.  
(6")  
2x4 Anti-  
Tip block  
If the Microwave Drawer is ever moved to a different location, the  
Anti-Tip block must also be moved and installed. When installed  
to the wall, make sure that the screws completely penetrate the  
dry wall and are secured in wood or metal so that the block is  
totally stable. When fastening, be sure that the screws do not  
penetrate electrical wiring or plumbing.  
Figure 4  
3
 
INSTALLATION MANUAL  
DRAWER INSTALLATION  
ELECTRICAL OUTLET  
electrical outlet location  
5"  
4"  
Figure 6  
Figure 5  
Parts Supplied  
4 Screws  
1. Place the drawer adjacent to the wall or  
cabinet opening. Plug the power supply cord  
into the electrical outlet.  
The electrical requirements are a 120 volt 60 Hz, AC only, 15  
amp. or more protected electrical supply. It is recommended that  
a separate circuit serving only this appliance be provided.  
2. Carefully guide the drawer into the prepared  
opening. Avoid pinching the cord between  
the oven and the wall.  
The drawer is equipped with a 3-prong grounding plug. It must  
be plugged into a wall receptacle that is properly installed and  
grounded. Should you only have a 2-prong outlet, have a qualified  
electrician install a correct wall receptacle.  
3. Slide the drawer all the way until the mounting flange is flush  
with the face of the cabinet.  
Note:
If you have any questions about the grounding or electrical  
instructions, consult a qualified electrician or service person.  
4. Secure the drawer with the 4 screws supplied. See Figure 6.  
MODEL AND SERIAL NUMBER LOCATION  
The name plate, including model and serial number, is located  
on the faceplate behind the Microwave Drawer front.  
GROUNDING INSTRUCTIONS  
This appliance must be grounded. The Microwave Drawer is  
equipped with a cord having a grounding wire with a grounding  
plug. It must be plugged into a wall receptacle that is properly  
installed and grounded in accordance with the National  
Electrical Code and local codes  
CARE, CLEANING AND MAINTENANCE  
Refer to the Operation Manual for cleaning instructions.  
Permanent and Correct Installation  
and ordinances. In the event  
of an electrical short circuit,  
grounding reduces risk of  
electric shock by providing  
an escape wire for the electric  
current.  
3-Prong Plug  
BEFORE YOU CALL FOR SERVICE  
Read the BEFORE YOU CALL and operating instruction sections  
in your Operation Manual. It may save you time and expense.  
The list includes common occurrences that are not the result of  
defective workmanship or materials in this range.  
Grounding Pin  
– Improper use  
of the grounding plug can result  
in a risk of electric shock.  
3-Prong Receptacle  
Ground Receptacle Box  
Refer to the warranty in your Operation Manual for Sharpʼs  
toll-free service number and address. Please call or write if you  
have inquiries about your microwave product and/or need to  
order parts.  
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07430-2135  
PRINTED IN USA  
TINSEB417MRR0  
 

Snell Acoustics Speaker AMC 870 User Manual
Sony Camcorder CCD TR86 User Manual
Sony CRT Television KDL 46XBR2 User Manual
Sony Digital Camera 4 143 374 111 User Manual
Sony Projector ES7 User Manual
Star Tech Development TV Cables HDMIPATRN2EU User Manual
Sterling Plumbing Product BP1012 User Manual
Stiga Lawn Mower 13 2511 21 User Manual
SVAT Electronics Security Camera 200 User Manual
Sylvania TV DVD Combo LD155SL8 User Manual