Sony Flat Panel Television 4 180 175 111 User Manual

4-180-175-11(1)  
Setting Up  
LCD  
Watching TV  
Digital Colour TV  
Operating Instructions  
Additional Information  
KDL-52HX903 / 46HX903 / 46HX803 / 40HX803  
 
Table of Contents  
Operating instructions are built into your BRAVIA TV. Refer to “To use i-Manual” for operation (page 9).  
Before operating the TV, please read “Safety Information” (page 16). Retain this manual for future reference.  
Checking the accessories  
AC power cord (mains lead) (1)  
Cable holder (1)  
Inserting batteries into the  
remote  
Remote (1)  
Size AAA batteries (R3 type) (2)  
Table-Top Stand (1)*1  
Fixing screws for Table-Top Stand  
(M5 × 16) (4)  
Assembling screws for Table-Top Stand  
(M5 × 16) (4)  
(KDL-40HX803 only)  
Stand rear cover (1)*2  
1
* For KDL-40HX803, assemble the Table-Top  
Stand with the supplied assembling screws.  
Refer to the supplied Table-Top Stand leaflet to  
assemble the stand.  
* For KDL-46HX803, the stand rear cover is  
factory-attached to the Table-Top Stand.  
1 Remove the protection sheet.  
2
2 Push and slide the cover upward.  
3GB  
 
     
Setting Up  
Adjusting the viewing angle of  
the TV (KDL-52/46HX903 only)  
This TV can be adjusted within the angles  
shown below.  
Attaching the Table-Top  
Stand  
1 Refer to the supplied Table-Top Stand  
leaflet for proper attachment for some  
TV models.  
0º  
6º  
2 Place the TV set on the Table-Top  
Stand.  
3 Fix the TV to the Table-Top Stand  
according to the arrow marks that  
guide the screw holes using the  
supplied screws.  
1
4
~
Remove screw as  
shown.  
Install screw into  
the top screw hole  
of the Table-Top  
Stand.  
If using an electric screwdriver, set the tightening  
torque at approximately 1.5 N·m {15 kgf·cm}.  
4 For KDL-52/46HX903 and KDL-  
40HX803, after all the screws are  
tightened, attach the supplied stand rear  
cover to the Table-Top Stand.  
2
3
Lift up and tilt.  
Slide in.  
~
To return to 0°, reverse the above procedure.  
4GB  
 
   
Connecting an antenna  
(aerial)/Set Top Box/  
Preventing the TV from  
toppling over  
recorder (e.g. DVD recorder)  
Connecting a Set Top Box/recorder  
(e.g. DVD recorder) with SCART  
Set Top Box/recorder (e.g. DVD recorder)  
1 Install a wood screw (4 mm in  
diameter, not supplied) in the TV stand.  
Connecting a Set Top Box/recorder  
(e.g. DVD recorder) with HDMI  
2 Install a machine screw (M4 × 16, not  
supplied) into the screw hole of the TV.  
3 Tie the wood screw and the machine  
screw with a strong cord (not supplied).  
Set Top Box/recorder (e.g. DVD recorder)  
5GB  
 
   
Bundling the cables  
Performing the initial set-up  
1 Connect the TV to your AC power  
outlet (mains socket).  
2 Check the ENERGY SAVING  
SWITCH setting is on (z).  
3 Press 1 on the TV.  
When you switch on the TV for the first  
time, the Language menu appears on the  
screen.  
4
~
Do not bundle the AC power cord (mains lead)  
together with other cables.  
Follow the instructions on the screen.  
Digital Auto Tuning: When you select  
“Cable”, we recommend that you select  
“Quick Scan” for quick tuning. Set  
“Frequency” and “Network ID” according  
to the information supplied from your cable  
provider. If no channel is found using  
“Quick Scan”, try “Full Scan” (though it  
may take some time).  
For a list of compatible cable providers,  
refer to the support web site:  
DVBC/  
6GB  
 
   
Programme Sorting: Changes the order of  
analogue channels stored in the TV.  
1 Press F/f to select the channel you want  
to move to a new position, then press  
.
2 Press F/f to select the new position for  
the channel, then press  
.
~
You can also tune channels manually.  
Detaching the Table-Top  
Stand from the TV  
~
For KDL-52/46HX903 and KDL-40HX803,  
remove the stand rear cover prior to detaching the  
Table-Top Stand.  
Remove the screws guided by the arrow marks  
of the TV.  
Do not remove the Table-Top Stand for any  
reason other than to install corresponding  
accessories on the TV.  
Do not hold by the stand rear cover while carrying  
the Table-Top Stand to prevent dropping the stand  
which may cause an injury or damage to the  
property.  
7GB  
 
   
Watching TV  
To watch programmes  
Turn on the TV.  
1
2
GUIDE  
1 Switch ENERGY SAVING SWITCH  
on (z).  
2 Press 1 on the TV to turn on the TV.  
OPTIONS  
HOME  
Select a mode.  
2
3
Select a TV channel.  
3
Using Digital Electronic Programme  
Guide  
Press GUIDE in digital mode to display the  
programme guide.  
z
The number 5, N, PROG + and AUDIO  
buttons on the remote have a tactile dot.  
Use the tactile dots as a reference when  
operating the TV.  
To utilise the TV’s features  
HOME button  
OPTIONS button  
Press to display various operation and setting  
screens.  
Press to display convenient functions based on  
the current input or content.  
Picture  
Sound  
SCART REC on  
Add to Favourites  
Lock/Unlock  
PAP  
Settings  
System Settings  
Motionflow  
Scene Select  
Sleep Timer  
Headphone Volume  
Speakers  
TV  
8GB  
 
     
To use i-Manual  
Operating instructions are built into your BRAVIA  
TV and can be displayed on the screen.  
To learn more about your TVs features you can  
access your i-Manual with the touch of a button.  
1
2
Press i-MANUAL.  
1
Press G/g/F/f/ to select items.  
2
x Welcome to i-Manual  
x “BRAVIA” TV Features  
x Watching TV  
x Fun Features with Connected  
Equipment  
Introduces how to connect optional equipment.  
x Parts Description  
Introduces convenient features such as EPG  
Guide, Favourites, etc.  
x Troubleshooting  
Find solutions for your problem.  
x Using the Home Menu  
Customise your TV settings, etc.  
~
x Index  
Images and illustrations may differ from what is displayed on the screen.  
9GB  
 
   
Additional Information  
Troubleshooting  
Check whether the 1 (standby) indicator is flashing in red.  
When the 1 (standby) indicator is flashing  
The self-diagnosis function is activated.  
1 Count how many times the 1 (standby) indicator flashes between each three second  
break.  
For example, the indicator may flash three times, go off for three seconds, then flash again three  
times.  
2 Press 1 on the TV to turn it off, disconnect the AC power cord (mains lead), and inform  
your dealer or Sony service centre of how the indicator flashes (number of flashes).  
When the 1 (standby) indicator is not flashing  
1 Check the items in the tables below. (Also refer to “Troubleshooting” in the i-Manual.)  
2 If the problem persists, have your TV serviced by qualified service personnel.  
Condition  
Explanation/Solution  
Picture  
There is no picture (screen Check the antenna (aerial)/cable connection.  
Connect the TV to the AC power (mains), and press 1 on the TV.  
If the 1 (standby) indicator lights up in red, press "/1 or TV "/1  
(button name differs by the remote).  
is dark) and no sound.  
Tiny black points and/or  
bright points appear on the  
screen.  
The screen is composed of pixels. Tiny black points and/or bright  
points (pixels) on the screen do not indicate a malfunction.  
General  
The TV’s power cannot be Check if ENERGY SAVING SWITCH is on (z).  
turned on.  
The TV turns off  
automatically (the TV  
enters standby mode).  
Check if the “Sleep Timer” is activated, or confirm the  
“Duration” setting of “On Timer”.  
Check if the “Idle TV Standby” is activated.  
The remote does not  
function.  
Replace the batteries.  
Your TV may be in SYNC mode.  
Press SYNC MENU, select “TV Control” and then select “Home  
(Menu)” or “Options” to control the TV.  
The “Parental Lock”  
password has been  
forgotten.  
Enter 9999 for the PIN code. (PIN code 9999 is always accepted.)  
The TV surrounds become When the TV is used for an extended period, the TV surrounds  
become warm. You may feel hot when touching there by the  
hand.  
warm.  
10GB  
 
   
Specifications  
System  
LCD (Liquid Crystal Display) Panel  
Panel system  
TV system  
Analogue: Depending on your country/area selection: B/G/H, D/K, L, I  
Digital: DVB-T2/DVB-T/DVB-C  
Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input)  
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC MP/HP@L4  
Colour/video system  
Channel coverage  
Analogue: VHF: E2–E12/UHF: E21–E69/CATV: S1–S20/HYPER: S21–S41  
D/K: R1–R12, R21–R69/L: F2–F10, B–Q, F21–F69/I: UHF B21–B69  
Digital: VHF/UHF  
10 W + 10 W  
Sound output  
Input/Output jacks  
Antenna (aerial) cable  
75 ohm external terminal for VHF/UHF  
21-pin scart connector (CENELEC standard) including audio/video input, RGB input and TV audio/video  
output.  
/
AV1, 2  
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i  
Audio input (phono jacks)  
COMPONENT IN  
COMPONENT IN  
HDMI IN1, 2, 3, 4  
Video: 1080/24p, 1080p, 1080i, 720/24p, 720p, 576p, 576i, 480p, 480i  
Audio: Two channel linear PCM: 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital  
Analogue audio input (minijack) (HDMI IN4 only)  
PC Input  
Video input (phono jack)  
AV3  
AV3  
Audio input (phono jacks)  
Digital optical jack (Two channel linear PCM, Dolby Digital)  
DIGITAL AUDIO OUT  
(OPTICAL)  
Audio output (phono jacks)  
(VAR/FIX)  
PC IN  
PC Input (Mini D-sub 15-pin)  
PC audio input (minijack)  
USB port  
Headphones jack  
i
CAM (Conditional Access Module) slot  
10BASE-T/100BASE-TX connector (Depending on the operating environment of the network,  
connection speed may differ. 10BASE-T/100BASE-TX communication rate and communication quality  
are not guaranteed for this TV.)  
LAN  
* For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied).  
3D Sync terminal for optional transmitter  
3D SYNC  
(Continued) 11GB  
 
 
Model name KDL-  
Power and others  
Power requirements  
52HX903  
46HX903  
46HX803  
40HX803  
220 V – 240 V AC, 50 Hz  
Approx. 132.2 cm/  
52 inches  
Approx. 116.8 cm/46 inches  
Approx. 101.6 cm/  
40 inches  
Screen size (measured  
diagonally)  
1,920 dots (horizontal) × 1,080 lines (vertical)  
Display resolution  
136 W  
130 W  
102 W  
149 W  
88.0 W  
132 W  
Power  
in “Home”/  
consumption “Standard”  
mode  
201 W  
184 W  
in “Shop”/  
“Vivid” mode  
0.2 W (14 W when “Quick Start” is set to “On”)  
199 kWh 190 kWh  
Standby power  
consumption*  
1
149 kWh  
128 kWh  
Average annual energy  
2
consumption*  
Dimensions (Approx.) (w × h × d)  
126.3 × 80.7 × 40.0 cm 112.4 × 72.7 × 40.0 cm 108.5 × 68.8 × 26.0 cm 95.2 × 61.3 × 25.0 cm  
with Table-Top Stand  
without Table-Top Stand  
Mass (Approx.)  
126.3 × 77.5 × 6.7 cm  
112.4 × 69.5 × 6.7 cm  
108.5 × 65.6 × 7.4 cm  
95.2 × 58.1 × 7.4 cm  
42.9 kg  
36.9 kg  
36.2 kg  
30.2 kg  
19.2 kg  
16.9 kg  
16.4 kg  
14.2 kg  
with Table-Top Stand  
without Table-Top Stand  
Supplied accessories  
Optional accessories  
Wall-Mount Bracket: SU-WL500  
TV stand: SU-52HX1 (KDL-52HX903)  
SU-46HX1 (KDL-46HX903)  
3D Glasses: TDG-BR100/TDG-BR50  
3D Sync Transmitter: TMR-BR100  
1
* Specified standby power is reached after the TV finishes necessary internal processes.  
2
* 4 hours a days and 365 days a year  
~
To save power consumption  
when you reduce backlight setting (the brightness of the screen), the power consumption reduce.  
the “Eco” settings (e.g. “Power Saving”, “Idle TV Standby”) help you to reduce the power consumption and  
thus save money by reducing electricity bills.  
when you switch off the TV using the ENERGY SAVING SWITCH, power consumption will be almost  
zero.  
Design and specifications are subject to change without notice.  
12GB  
 
 
Installing the Accessories (Wall-Mount Bracket)  
To Customers:  
For product protection and safety reasons, Sony strongly recommends that installing of your TV be  
performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.  
To Sony Dealers and Contractors:  
Provide full attention to safety during the installation, periodic maintenance and examination of this  
product.  
Your TV can be installed using the SU-WL500 Wall-Mount Bracket (sold separately).  
Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the  
installation.  
~
Place the TV on the Table-Top Stand, when securing the Mounting Hook.  
Screw  
(+PSW  
6 × 16)  
Square hole  
Mounting Hook  
Sufficient expertise is required for installing this product, especially to determine the strength of  
the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the  
wall to Sony dealers or licensed contractors and pay adequate attention to safety during the  
installation. Sony is not liable for any damage or injury caused by mishandling or improper  
installation.  
(Continued) 13GB  
 
 
TV installation dimensions table  
Screen centre point  
Unit: cm  
Length for each mounting angle  
Display  
dimensions  
Screencentre  
dimension  
Model Name  
KDL-  
Angle (0°)  
Angle (20°)  
A
B
C
7.7  
D
E
F
34.8  
32.0  
32.3  
29.7  
G
73.5  
65.9  
61.6  
54.6  
H
50.6  
50.6  
45.4  
45.4  
126.3  
112.4  
108.5  
95.2  
77.5  
69.5  
65.6  
58.1  
48.2  
48.2  
43.1  
43.1  
12.0  
12.0  
12.1  
12.0  
52HX903  
11.8  
9.5  
46HX903  
46HX803  
40HX803  
13.3  
Figures in the above table may differ slightly depending on the installation.  
WARNING  
The wall that the TV will be installed on should be capable of supporting a weight of at least four  
times that of the TV. Refer to “Specifications” (page 12) for its weight.  
14GB  
 
Screw and Hook locations diagram/table  
Model Name  
Screw location  
Hook location  
b
KDL-52HX903  
KDL-46HX903/46HX803  
KDL-40HX803  
e, j  
Screw location  
Hook location  
When installing the Mounting Hook on the  
TV.  
When installing the TV onto the Base Bracket.  
a*  
b
c*  
* Hook location “a” and “c”  
cannot be used for the models.  
15GB  
 
Unplug the mains plug and clean it  
regularly. If the plug is covered with  
dust and it picks up moisture, its  
insulation may deteriorate, which  
could result in a fire.  
Ventilation  
Never cover the ventilation holes or  
Safety  
insert anything in the cabinet.  
Leave space around the TV set as shown  
below.  
Information  
It is strongly recommended that you use  
a Sony wall-mount bracket in order to  
provide adequate air-circulation.  
Notes  
Do not use the supplied mains lead on  
Installation/Set-up  
any other equipment.  
Install and use the TV set in accordance  
with the instructions below in order to  
avoid any risk of fire, electrical shock or  
damage and/or injuries.  
Installed on the wall  
Do not pinch, bend, or twist the mains  
lead excessively. The core conductors  
may be exposed or broken.  
Do not modify the mains lead.  
Do not put anything heavy on the mains  
lead.  
Do not pull on the mains lead itself when  
disconnecting the mains lead.  
Do not connect too many appliances to  
the same mains socket.  
Do not use a poor fitting mains socket.  
30 cm  
10 cm  
10 cm  
Installation  
The TV set should be installed near an  
easily accessible mains socket.  
Place the TV set on a stable, level  
surface.  
10 cm  
Only qualified service personnel should  
carry out wall installations.  
For safety reasons, it is strongly  
recommended that you use Sony  
accessories, including:  
Leave at least this space around  
the set.  
Prohibited Usage  
Do not install/use the TV set in locations,  
environments or situations such as those  
listed below, or the TV set may  
malfunction and cause a fire, electrical  
shock, damage and/or injuries.  
Installed with stand  
Wall-mount bracket SU-WL500  
30 cm  
TV stand:SU-52HX1  
(KDL-52HX903)  
SU-46HX1  
10 cm  
10 cm  
6 cm  
(KDL-46HX903)  
Location:  
Be sure to use the screws supplied with  
the Wall-mount bracket when attaching  
the mounting hooks to the TV set. The  
supplied screws are designed so that they  
are 8 mm to 12 mm in length when  
measured from the attaching surface of  
the mounting hook.  
The diameter and length of the screws  
differ depending on the Wall-mount  
bracket model.  
Outdoors (in direct sunlight), at the  
seashore, on a ship or other vessel, inside a  
vehicle, in medical institutions, unstable  
locations, near water, rain, moisture or  
smoke.  
Leave at least this space around  
the set.  
To ensure proper ventilation and prevent  
the collection of dirt or dust:  
Do not lay the TV set flat, install  
upside down, backwards, or  
sideways.  
Do not place the TV set on a shelf,  
rug, bed or in a closet.  
Do not cover the TV set with a cloth,  
such as curtains, or items such as  
newspapers, etc.  
Do not install the TV set as shown  
below.  
Environment:  
Places that are hot, humid, or excessively  
dusty; where insects may enter; where it  
might be exposed to mechanical vibration,  
near flammable objects (candles, etc). The  
TV set shall not be exposed to dripping or  
splashing and no objects filled with  
liquids, such as vases, shall be placed on  
the TV.  
Use of screws other than those supplied  
may result in internal damage to the TV  
set or cause it to fall, etc.  
8 mm - 12 mm  
Screw (supplied with the  
Wall-mount bracket)  
Situation:  
Air circulation is blocked.  
Do not use when your hands are wet, with  
the cabinet removed, or with attachments  
not recommended by the manufacturer.  
Disconnect the TV set from mains socket  
and aerial during lightning storms.  
Mounting Hook  
Hook attachment on rear  
of TV set  
Transporting  
Broken pieces:  
Do not throw anything at the TV set. The  
screen glass may break by the impact  
and cause serious injury.  
Before  
Wall  
Wall  
transporting the  
TV set, disconnect  
all cables.  
Two or three  
people are needed  
to transport a large  
TV set.  
When transporting  
the TV set by  
hand, hold it as  
shown on the  
right. Do not put  
stress on the LCD  
panel and the  
If the surface of the TV set cracks, do  
not touch it until you have unplugged the  
mains lead. Otherwise electric shock  
may result.  
Mains lead  
When not in use  
If you will not be using the TV set for  
several days, the TV set should be  
disconnected from the mains for  
environmental and safety reasons.  
As the TV set is not disconnected from  
the mains when the TV set is just turned  
off, pull the plug from the mains to  
disconnect the TV set completely.  
However, some TV sets may have  
features that require the TV set to be left  
in standby to work correctly.  
Handle the mains lead and socket as  
follows in order to avoid any risk of fire,  
electrical shock or damage and/or injuries:  
Use only mains leads supplied by  
Sony, not other suppliers.  
Insert the plug fully into the mains  
socket.  
Operate the TV set on a 220-240 V AC  
supply only.  
When wiring cables, be sure to unplug  
the mains lead for your safety and take  
care not to catch your feet on the  
cables.  
frame around the  
screen.  
For KDL-52/  
46HX903  
When lifting or  
moving the TV  
set, hold it firmly  
from the bottom.  
When transporting  
the TV set, do not  
subject it to jolts or  
excessive  
vibration.  
When transporting  
the TV set for  
repairs or when moving, pack it using  
the original carton and packing material.  
For children  
Do not allow children to climb on the  
TV set.  
Keep small accessories out of the reach  
of children, so that they are not  
mistakenly swallowed.  
Disconnect the mains lead from the  
mains socket before working on or  
moving the TV set.  
Keep the mains lead away from heat  
sources.  
For KDL-46/  
40HX803  
16GB  
 
   
image may be uneven or the LCD screen  
may be damaged.  
If this TV set is used in a cold place, a  
smear may occur in the picture or the  
picture may become dark. This does not  
indicate a failure. These phenomena  
disappear as the temperature rises.  
Ghosting may occur when still pictures  
are displayed continuously. It may  
disappear after a few moments.  
The screen and cabinet get warm when  
this TV set is in use. This is not a  
malfunction.  
If the following problems  
occur...  
Disposal of the TV set  
Disposal of Old  
Electrical &  
Electronic  
Equipment  
(Applicable in  
Turn off the TV set and unplug the mains  
lead immediately if any of the following  
problems occur.  
Ask your dealer or Sony service centre to  
have it checked by qualified service  
personnel.  
the European  
When:  
Union and other European  
countries with separate  
collection systems)  
This symbol on the product or on its  
packaging indicates that this product shall  
not be treated as household waste. Instead  
it shall be handed over to the applicable  
collection point for the recycling of  
electrical and electronic equipment. By  
ensuring this product is disposed of  
correctly, you will help prevent potential  
negative consequences for the  
Mains lead is damaged.  
Poor fitting of mains socket.  
TV set is damaged by being dropped,  
hit or having something thrown at it.  
The LCD screen contains a small  
amount of liquid crystal. Some  
fluorescent tubes used in this TV set also  
contain mercury. Follow your local  
ordinances and regulations for disposal.  
Any liquid or solid object falls through  
openings in the cabinet.  
Handling and cleaning the  
screen surface/cabinet of  
the TV set  
Be sure to unplug the mains lead  
connected to the TV set from mains socket  
before cleaning.  
Warning  
To prevent the spread of fire, keep candles  
or other open flames away from this  
product at all time.  
environment and human health, which  
could otherwise be caused by  
To avoid material degradation or screen  
coating degradation, observe the following  
precautions.  
inappropriate waste handling of this  
product. The recycling of materials will  
help to conserve natural resources. For  
more detailed information about recycling  
of this product, please contact your local  
Civic Office, your household waste  
disposal service or the shop where you  
purchased the product.  
To remove dust from the screen surface/  
cabinet, wipe gently with a soft cloth. If  
dust is persistent, wipe with a soft cloth  
slightly moistened with a diluted mild  
detergent solution.  
Do not spray water or detergent directly  
on the TV set. It may drip to the bottom  
of the screen or exterior parts, and may  
cause a malfunction.  
Never use any type of abrasive pad,  
alkaline/acid cleaner, scouring powder,  
or volatile solvent, such as alcohol,  
benzene, thinner or insecticide. Using  
such materials or maintaining prolonged  
contact with rubber or vinyl materials  
may result in damage to the screen  
surface and cabinet material.  
Periodic vacuuming of the ventilation  
openings is recommended to ensure to  
proper ventilation.  
When adjusting the angle of the TV set,  
move it slowly so as to prevent the TV  
set from moving or slipping off from its  
table stand.  
Precautions  
Viewing the TV  
Some people may experience discomfort  
(such as eye strain, fatigue, or nausea)  
while watching 3D video images or  
playing 3D video games. Sony  
recommends that all viewers take regular  
breaks while watching 3D video images  
or playing 3D video games. The length  
and frequency of necessary breaks will  
vary from person to person. You must  
decide what works best. If you  
Disposal of  
waste batteries  
(applicable in the  
European Union  
and other  
European  
countries with separate  
collection systems)  
experience any discomfort, you should  
stop watching the 3D video images or  
playing 3D video games until the  
This symbol on the battery or on the  
packaging indicates that the battery  
provided with this product shall not be  
treated as household waste. On certain  
batteries this symbol might be used in  
combination with a chemical symbol. The  
chemical symbols for mercury (Hg) or  
lead (Pb) are added if the battery contains  
more than 0.0005% mercury or 0.004%  
lead. By ensuring these batteries are  
disposed of correctly, you will help  
prevent potentially negative consequences  
for the environment and human health  
which could otherwise be caused by  
inappropriate waste handling of the  
battery. The recycling of the materials will  
help to conserve natural resources. In case  
of products that for safety, performance or  
data integrity reasons require a permanent  
connection with an incorporated battery,  
this battery should be replaced by qualified  
service staff only. To ensure that the  
battery will be treated properly, hand over  
the product at end-of-life to the applicable  
collection point for the recycling of  
electrical and electronic equipment. For all  
other batteries, please view the section on  
how to remove the battery from the  
product safely. Hand the battery over to  
the applicable collection point for the  
recycling of waste batteries. For more  
detailed information about recycling of  
this product or battery, please contact your  
local Civic Office, your household waste  
disposal service or the shop where you  
purchased the product.  
discomfort ends; consult a doctor if you  
believe necessary. You should also  
review (i) the instruction manual of any  
other device or media used with this  
television and (ii) our website (http://  
the latest information. The vision of  
young children (especially those under  
six years old) is still under development.  
Consult your doctor (such as a  
Optional Equipment  
Keep optional components or any  
equipment emitting electromagnetic  
radiation away from the TV set.  
Otherwise picture distortion and/or noisy  
sound may occur.  
pediatrician or eye doctor) before  
allowing young children to watch 3D  
video images or play 3D video games.  
Adults should supervise young children  
to ensure they follow the  
This equipment has been tested and  
found to comply with the limits set out in  
the EMC Directive using a connection  
signal cable shorter than 3 meters.  
recommendations listed above.  
When using the simulated 3D function,  
please note that the displayed image is  
modified from the original due to the  
conversion done by this television.  
View the TV in moderate light, as  
viewing the TV in poor light or during  
long period of time, strains your eyes.  
When using headphones, adjust the  
volume so as to avoid excessive levels,  
as hearing damage may result.  
Batteries  
Observe the correct polarity when  
inserting batteries.  
Do not use different types of batteries  
together or mix old and new batteries.  
Dispose of batteries in an  
environmentally friendly way. Certain  
regions may regulate the disposal of  
batteries. Please consult your local  
authority.  
Handle the remote with care. Do not  
drop or step on it, or spill liquid of any  
kind onto it.  
LCD Screen  
Although the LCD screen is made with  
high-precision technology and 99.99%  
or more of the pixels are effective, black  
dots may appear or bright points of light  
(red, blue, or green) may appear  
Do not place the remote in a location  
near a heat source, a place subject to  
direct sunlight, or a damp room.  
constantly on the LCD screen. This is a  
structural property of the LCD screen  
and is not a malfunction.  
Do not push or scratch the front filter, or  
place objects on top of this TV set. The  
17GB  
 
 
Keep this Instruction  
manual safe you’ll  
need it  
Television in the UK is going digital, bringing us all more.  
Please see overleaf to find out when your area switches to digital.  
Digital UK is the independent, non-profit organisation leading the process of digital TV switchover  
in the UK. Digital UK provides impartial information on what people need to do to prepare for the  
move to digital, and when they need to do it.  
How the switchover affects your TV equipment:  
Your new TV has a digital tuner built in, which means it is ready to receive the Freeview signal by  
simply plugging it into your aerial socket (check if you can get digital TV through your aerial now,  
or whether you'll have to wait until switchover, at www.digitaluk.co.uk).  
When the TV switchover happens in your area, there are at least two occasions when you will need  
to re-tune your TV in order to continue receiving your existing TV channels, and also to pick up new  
ones. Digital UK, the body leading the digital TV switchover, will advise you when you need to re-  
tune during the switchover.  
18GB  
 
How to re-tune:  
1
2
3
4
5
6
Press "HOME" on the remote  
Press G/g to select "Settings"  
Press F/f to select "Digital Set-up", then press  
Press to select "Digital Auto Tuning"  
Press G to select "Yes" then press to start "Digital Auto Tuning"  
Follow the on screen instructions.  
If you are missing any channels, it may be that they are not available in your area, or that your aerial  
needs upgrading.  
If you have any questions, please contact Sony on 08705 111 999 or call Digital UK on 0845 6 50 50  
†Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends.  
Rates may vary for calls from non-BT lines.  
19GB  
 
For useful information about Sony products  
4-180-175-11(1)  
© 2010 Sony Corporation  
 

Sennheiser Headphones PXC310 User Manual
Sharp Cash Register XE A21S User Manual
Shoprider Mobility Aid HD 888WHD User Manual
SIIG Computer Drive 04 0288E User Manual
Sony Car Stereo System NWZ A815 A816 A818 User Manual
Sony Headphones MDR F1 User Manual
Sony Speaker System SS XB3E User Manual
Speco Technologies Computer Monitor VM 1005C User Manual
Stiga Trimmer 13 6241 43 User Manual
Sylvania TV VCR Combo D6313CCB User Manual