Sony Universal Remote RM V201T User Manual

3-866-334-11(1)  
Se t t in g t h e Co m p o n e n t Co d e s  
Op e ra t in g a Co m p o n e n t  
Re m o t e Bu t t o n De scrip t io n s  
To use this Remote Commander with a Sony brand component that  
is already preset at the factory (see the table on the left), you can skip  
this procedure.  
If you are using other brands component or if you cannot operate  
even a Sony brand component, follow this procedure.  
1
Set the slide sw itch to the position of your component.  
Se t t in g b y Se a rch in g fo r t h e Co rre ct Co d e  
If youve tried all the code numbers listed for your component and  
you still cannot get the Commander to work (or if your component  
was not listed), try the following.  
RM-V201T  
Remote Commander  
Op e ra t in g a TV/Sa t e llit e Tu n e r  
TV  
Operating Instructions  
Mode demploi (au verso)  
1
0
!¡  
1 To switch to Teletext.  
2 To change the input mode.  
3 Fastext buttons.  
4 To change the programme.  
Also to turn on the power.  
5 To select double-digit numbers.  
Works in the same way as your  
TV’s commander.  
6 To move the cursor upward,  
downward, to the right or left.  
7 To call up the MENU display.  
8 Volume up: +  
1
2
Turn on the component you wish to set up using its power  
switch.  
Set the slide switch on the Remote Commander to the desired  
2
3
2
Point the Commander directly to your component and press  
the button for the desired function.  
See “Remote Button Descriptions” for details.  
Sony Corporation © 1999 Printed in Malaysia  
Se t t in g b y En t e rin g t h e Co d e Nu m b e r  
See the supplied “Component Code Numbers” and find the code for  
your component.  
position.  
3
4
Press the S (Set) button.  
4
No t e s o n u sin g t h e Co m m a n d e r  
Aim the Commander to your component, and press and release  
the PROGR+ button. Then press and release the u button.  
Repeat step 4 until the correct code number is found.  
Each time you press the PROGR+ button and then the u button, a  
new code number will be transmitted.  
• Using this Commander will not add new functions to your components. The  
functions of the Commander are limited to the functions of the component  
itself. For example, if your TV does not have a mute function, the ¤ button  
on this Commander will not function with your TV.  
1
Set the slide sw itch to the position that corresponds to the  
component to set up.  
English  
5
5
!™  
6
7
• Do not forcibly remove or tear off the corner protector.  
!£  
!¢  
Keep trying until your component operates as follows:  
• TV, VCR or satellite tuner : the power turns off.  
• TV without a power switch: the Channel + function works.  
Ab o u t t h is Re m o t e Co m m a n d e r  
In st a llin g t h e Ba t t e rie s  
Volume down: –  
8
9
9 To mute volume on TV.  
0 To turn off the power.  
To turn on.  
To return from Teletext to TV.  
!™ To select a number between 20  
and 29.  
You can set up this Remote Commander to operate the following  
components of almost all major brands including Sony.  
Open the battery compartment and insert two R6 (size AA) batteries  
(not supplied).  
To se t u p ...  
a TV  
Se t t h e slid e sw it ch t o ...  
Tro u b le sh o o t in g  
If youre having problems setting up or using the Remote  
Commander:  
Be patient as you do this; it may take up to about 100 tries for a  
TV, and 70 to 80 tries for other components until the correct code  
number is located.  
!∞  
Be sure to line up the + and – on the batteries with the + and – on the  
battery compartment.  
TV  
Po sit io n  
TV  
Fa ct o ry se t t in g  
Co m p o n e n t t h a t ca n b e p re se t  
a satellite tuner  
a VCR  
SAT  
Sony TV  
TV  
6
7
When the correct code is found, press the button.  
Turn on the component again, and check that the Commander  
can control the other functions of your component such as  
channel and volume control.  
VCR or AUX  
• When setting up the Commander, carefully go through the  
procedures described under “Setting the Component Codes”. If the  
code thats listed first for your component doesnt work, try all the  
codes for your component — in the order in which theyre listed. If  
all the codes fail to work (or if your component is not listed), try  
using the procedures under “Setting by Searching for the Correct  
Code”.  
• Check that youre aiming the Commander directly at the  
component, and that there are no obstructions between the  
Commander and the component.  
VCR  
Sony VHS VCR (VTR3) VCR  
Sony DV (VTR4)  
1
2
To enter the selection.  
Programme up: +  
Programme down: –  
!To operate JUMP,  
AUX  
SAT  
2
3
Press the S (set) button.  
TV, VCR, or satellite tuner  
Sony satellite tuner  
If the component does not operate properly, repeat steps 3 to 6 and  
search for another code.  
FLASHBACK, or CHANNEL  
on the TV, depending on the  
manufacturers setting.  
Enter the three-digit component code in the “Component  
Code Numbers” table.  
If you still cannot get the Commander to work properly, see  
“Troubleshooting”.  
Sp e cifica t io n s  
Operable distance  
For example, to set a Philips’ TV, press  
.
Sa t e llit e Tu n e r  
No t e  
Be sure to proceed to each next step in the above procedure within 10 seconds;  
otherwise setting mode will be canceled.  
Wh e n t o re p la ce t h e b a t t e rie s  
• Make sure the batteries youre using are not worn out, and that  
theyre inserted correctly.  
Approx. 10 m (33 ft) (varies depending on the component of  
each manufacturer)  
2 To change the input mode  
!™ To select a number between 20  
and 29.  
Under normal conditions, batteries will last up to six months. If the  
Remote Commander does not operate properly, the batteries might  
be worn out. Replace the batteries with new ones.  
(H/ V).  
• Check that the slide switch of the Remote Commander is set to the  
position (TV, VCR, SAT or AUX) for your desired component.  
• If you cannot preset a component to the AUX or SAT position of  
the slide switch, a component type different from that of the  
component you intend to preset may be assigned to that position.  
In such a case, follow the procedure in “Setting Another TV, VCR,  
or Satellite Tuner” first.  
• Check that the component has infrared remote capability. For  
example, if your component didnt come with a remote control, it  
probably isnt capable of being controlled by the Remote  
Commander.  
Pow er requirements  
Two R6 (size AA) batteries (not supplied)  
Battery life  
4 To change the programme.  
To enter the selection.  
Se t t in g An o t h e r TV, VCR, o r Sa t e llit e Tu n e r  
When you have two or more components of the same type (for  
example, three VCRs), you can set the code number of the  
components type on any empty position of the slide switch of the  
Remote Commander (AUX or SAT position only).  
5 To select double-digit numbers. Programme up: +  
Work in the same way as your  
satellite tuners commander.  
Programme down: –  
!To operate JUMP,  
No t e s  
4
5
Press the button.  
Approx. six months (varies depending on frequency of use)  
Dimensions  
• Replace both batteries with new ones.  
• Do not take more than 20 minutes to replace the batteries; otherwise, your  
setting of the code numbers will be erased.  
6 To move the cursor upward,  
downward, to the right or left.  
7 To call up the MENU display.  
8 To control the volume on TV.  
9 To mute the volume on TV.  
0 To turn on and off the power.  
FLASHBACK or CHANNEL  
RETURN function on the  
satellite tuner, depending on  
the manufacturers setting.  
Approx. 63 × 200 × 38 mm (w/ h/ d) (2 1/  
Mass  
2
× 7 7/  
8
× 1 1/  
in.)  
2
1
2
3
4
Set the slide switch on the Remote Commander to AUX or SAT.  
Press the S (Set) button.  
Press the p button.  
Press one of the following buttons;  
1 to set up a VCR  
Aim this Commander to your component and check if you can  
operate it using this Commander.  
Approx. 120 g (4.2 oz.) (not including batteries)  
No t e s o n Ba t t e rie s  
• Do not mix old batteries with new ones or mix different types of  
batteries together.  
Design and specifications are subject to change without notice.  
Go through the same procedure for each component you want to set  
up.  
• If the electrolyte inside the battery should leak, wipe the  
contaminated area of the battery compartment with a cloth and  
replace the old batteries with new ones. To prevent the electrolyte  
from leaking, remove the batteries when you plan not to use the  
Commander for a long period of time.  
• Should any problem persist, reset the Commander to the factory  
setting by pressing the u, and Ábuttons simultaneously.  
8 to set up a TV  
9 to set up a satellite tuner  
If yo u ca n n o t o p e ra t e yo u r co m p o n e n t ...  
• First, try repeating these set up procedures using the other codes  
listed for your component (see “Component Code Numbers”).  
• If — after trying all the codes listed for your component — you still  
cannot get the Commander to work properly, try the search  
method described under “Setting by Searching for the Correct  
Code”.  
Op e ra t in g a VCR  
If you have any questions or problems concerning the Remote  
Commander that are not covered in this manual, please call the  
telephone number in the warranty.  
5
6
Press the button.  
Enter the components code number by following steps 2 to 5 of  
“Setting by Entering the Code Number”, or steps 3 to 7 of  
“Setting by Searching for the Correct Code”.  
1 To switch the signals supplied to  
the TV.  
2 To change the programme.  
3 To select double-digit numbers.  
Works in the same way as your  
VCR’s commander.  
9
1
No t e s  
4 To play  
5 To rewind  
2
3
4
• Be sure to proceed to each next step in the above procedure within 10  
seconds; otherwise, the setting mode will be canceled.  
• You cannot set up more than one component at a time on each position of the  
slide switch. If you want to set up two or more same components of different  
brands, see “Setting Another TV, VCR, or Satellite Tuner”.  
6 To record, press ( while  
pressing r.  
7 To control the volume on TV.  
8 To mute the volume on TV.  
9 To turn on and off the power.  
0 To select a number between 20  
and 29.  
To fast-forward  
!™ To stop  
To pause  
Programme up: +  
Programme down: –  
0
!¡  
!™  
!£  
!¢  
5
6
Tip  
You can write down the code number on the label inside the battery  
compartment lid.  
7
8
 

SIIG Film Camera 04 0414D User Manual
Sonance Speaker X8WR User Manual
Sony Computer Drive MPF88E UA User Manual
Sony TV VCR Combo SU GW11 User Manual
Sony VCR GV D200 User Manual
Southwestern Bell Cordless Telephone GH3210 User Manual
Speco Technologies Security Camera CVC 637EX User Manual
SPX Cooling Technologies Refrigerator 05 116E User Manual
Stiga Lawn Mower 125 M User Manual
Sylvania TV VCR Combo 6309CCB User Manual