Specialized Bicycle Sirrus Ltd Expert User Manual

BICYCLE/FRAME INSTRUCTION GUIDE  
TARMAC/ROUBAIX/RUBY/SW TRICROSS/SIRRUS LTD - EXPERT/PRO/S-WORKS SL  
THIS BRIEF INSTALLATION GUIDE CONTAINS IMPORTANT INFORMATION.  
PLEASE READ CAREFULLY AND STORE IN A SAFE PLACE.  
Congratulations! The Specialized bicycle you have chosen is among  
the finest of advanced composite products available in cycling.  
Carbon fiber is a very special material that requires particular care  
during assembly, storage and riding. This short form installation guide  
contains instructions and warnings, plus torque specifications.  
The seat post is marked with a minimum insertion line, which is the  
minimum insertion required for the seat post to remain structurally safe.  
WARNING! Do not extend seat post above the minimum inser-  
tion line. Extension beyond the minimum insertion line can  
result in failure.  
Please read the following instructions. If you have any doubt regarding  
your mechanical ability and/or installation of this product, visit your  
local authorized dealer. Specialized recommends that components be  
installed on the frame using a torque wrench, by a qualified mechanic.  
HEADSET  
Your Specialized frame does not require any head tube  
pre-installation preparation. All surfaces are already  
prepared from the factory, with the exception of  
greasing the cups.  
1
Please read the following Warnings. Because the failure to follow any  
Warning may result in a catastrophic failure of the frame, resulting in  
serious personal injury or death, this phrase may not be repeated in  
connection with each Warning.  
2
3
Use 42mm Campagnolo Standard compatible bear-  
ings. No tools are required for installation or removal of  
42mm Campagnolo Standard MindSet bearings.  
To ensure the best assembly possible and to prevent any damage  
to the components or frame, follow all torque specifications. Please  
refer to the specific owner’s manual for mating component’s correct  
torque specifications. If the mating component’s recommended torque  
exceeds the frame’s recommended torque, use the lower torque spec.  
Due to torque considerations, not all components will be compatible.  
BOTTOM BRACKET  
1. Cone spacer/cap  
2. Compression ring  
3. 1 1/8” Bearing  
4. Crown race  
Your Specialized frame does not require any bottom  
bracket pre-installation preparation. All surfaces are  
already prepared from the factory, with the exception  
of greasing the threads. It is acceptable to chase  
the threads if applicable and necessary. Do not face  
bottom bracket cups.  
WARNING! Failure to follow the torque specifications in this  
installation guide will void the warranty, but most importantly  
may result in damage to the frame which may not be visible.  
If the frame is damaged, this can result in loss of structural  
integrity, which may result in serious personal injury or death.  
THREADED: Ensure that the bottom bracket shell  
threads are clean and greased prior to installation.  
Recommended torque is 442 in-lbf (50 N-m).  
Bicycle components such as a handlebar, handlebar stem, seat post,  
saddle, brakes, all must be compatible with each other, the frame  
and the intended use. Any doubt regarding compatibility should be  
discussed with your local authorized Specialized retailer.  
OVERSIZED BB: Please refer to the carbon crank  
installation guide for assembly instructions and  
compatible tools.  
3
4
WARNING! When placing the frame and/or bicycle in a repair  
stand, clamp the stand to the seat post and not the frame.  
Clamping the frame can cause damage to the frame that may  
or may not be visible.  
SEAT POST / SADDLE INSTALLATION  
COMPONENT TORQUE SETTINGS  
Refer to your seat post installation guide prior to installation.  
Specialized road frames have a 27.2mm seat post diameter and require  
that the seat post have a tolerance of 27.08mm to 27.25mm.  
The Tarmac, Roubaix and Ruby Expert/Pro/S-Works SL frames use  
a seat post collar specifically designed for these frames. Use of a  
different collar can cause damage to the frame or seatpost, resulting in  
failure (see fig.1 for proper setup).  
• Front derailleur: Recommended torque is 44 in-lbf (5.0 N-m).  
• Rear derailleur: Recommended torque for the rear derailleur is 70  
in-lbf (7.9 N-m). Ensure that threads are clean prior to installation.  
• Seat collar: Recommended torque is 55 in-lbf (6.2 N-m).  
• Water Bottle Cage: Recommended torque is 35 in-lbf (4.0 N-m).  
To avoid damage to the bottle cage frame rivets, ensure that  
the cage doesn’t flex around the front derailleur clamp. If the cage  
doesn’t clear the clamp, use longer bolts and spacers to help the  
cage clear the derailleur clamp.  
Tighten seat collar bolt to recommended torque of 55 in-lbf (6.2 N-m).  
°
Turn collar slot 180 opposite  
Fig.1  
from frame slot  
WARNING! Great care should be taken not to damage composite  
materials, including the frame and any composite components.  
Any damage may result in a loss of structural integrity, which may  
result in a catastrophic failure. This damage may not be visible in  
inspection. Before each ride, and after any crash, carefully inspect  
the bicycle for and dents, fraying, gouging, scratches through the  
paint, chipping, bending or any other signs of damage. Do not  
ride if the bicycle shows any signs of these signs. After any crash,  
and before riding any further, take the bicycle to an authorized  
Specialized retailer for a complete inspection.  
FRAME SLOT  
27.2mm  
Grease bolt threads  
Recommended Torque:  
55 in-lbf (6.2 N-m)  
Alloy shim  
CHAMFER SEAT TUBE EDGES  
• Full radius of top edge  
• Along full length of frame slot  
• SEAT TUBE I.D.  
• SEAT POST O.D.  
WARNING! Do not grease the seat tube surface that contacts WARRANTY  
the seat post. Grease reduces the friction that is critical to  
For the complete warranty provisions and any additional information,  
proper seat post grip. Remove any grease from the surfaces  
of the seat tube and seat post.  
TECH TIP: Specialized recommends the application of carbon  
assembly compound between the seat tube and post to increase  
See your authorized Specialized retailer if you have any questions.  
SPECIALIZED BICYCLE COMPONENTS  
15130 Concord Circle, Morgan Hill, CA 95037 (408) 779-6229  
Please note all instructions are subject to change for improvement without notice.  
Rev.1, May 2007  
 

Sennheiser Music Mixer TI 200 User Manual
Snapper Lawn Aerator 4576 User Manual
Sony Cell Phone LT30at User Manual
Sony Headphones SCEH 00075 User Manual
SoundMax Portable DVD Player SM CMD3000 User Manual
Sprint Nextel Cell Phone LG OPTIMUS F3 User Manual
Sterling Planer SSV 05 R User Manual
Sunbeam Toaster 6198 33 User Manual
Syba Tech Computer Accessories CLCRD50007 User Manual
Sylvania TV VCR Combo 3819LC User Manual