Sunbeam Freezer SBUF3W User Manual

UPRIGHT FREEZER  
INSTRUCTION MANUAL  
Model No.: SBUF3W  
© 2010 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved.  
SUNBEAM® logo is a registered trademark of Sunbeam Products, Inc. used under license.  
Distributed by MC Appliance Corporation, 777 Mark Street, Wood Dale, IL 60191  
For service, support and warranty information, visit www.mcappliance.com or in the US call 877 856-0202.  
To ensure proper use of this appliance and your safety, please read the  
following instructions completely before operating this appliance.  
 
freezer.  
NAMES OF THE PARTS  
The freezer is touching the wall. Re-level the  
freezer and move it from the wall.  
See “Installation Instructions”.  
Moisture forms on inside freezer walls.  
Weather is hot and humid, which increases  
internal rate of frost build-up. This is normal.  
Door is slightly open.  
MODEL NO. SBUF3W  
Door is kept open too long, or is opened too  
frequently. Open the door less often.  
The door is not sealed properly.  
Moisture forms on outside of freezer.  
The door will not close properly.  
Door is slightly open, causing cold air from inside  
the freezer to meet warm moist air from outside.  
The freezer is not on a level surface.  
The gasket is dirty.  
1
2
3
1.  
2.  
3.  
Thermostat Dial  
Evaporator Shelves  
Magnetic Gasket  
WARNING : Never touch the interior of the Freezer Chamber or frozen foods in the  
compartment with wet hands as this could result in frost bite.  
9
2
 
IMPORTANT SAFETY INSTRUCTIONS  
TROUBLESHOOTING GUIDE  
To reduce the risk of fire, electrical shock, or  
injury when using your freezer, follow these  
basic precautions:  
WARNING  
You can solve many common freezer problems easily, saving you the cost of a possible  
service call. Try the suggestions below to see if you can solve the problem before calling for  
service.  
Read all instructions before using the freezer.  
DANGER or WARNING: Risk of child entrapment.  
To avoid the possibility of child entrapment, please take the following precautions:  
Never allow children to operate, play with, or crawl inside the freezer.  
Before you throw away your old freezer: Take off the door so that children may not easily  
be entrapped.  
It is dangerous to alter the specifications or attempt to modify this product in any way.  
Never clean freezer parts with flammable fluids. The fumes can create a fire hazard or  
explosion.  
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this  
or any other freezer. The fumes can create a fire hazard or an explosion.  
All freezer products contain refrigerants, which under the guidelines of federal law must  
be removed before disposal. It is the consumer’s responsibility to comply with federal and  
local regulations when disposing of this unit.  
PROBLEM  
Freezer does not operate.  
POSSIBLE CAUSE  
Not plugged in.  
The circuit breaker tripped or a blown fuse.  
The room temperature is hotter than normal.  
A large amount of food has been added to the  
freezer.  
The door is opened too often.  
The door is not closed completely.  
The temperature control is not set correctly.  
The door gasket does not seal properly.  
The freezer does not have the correct  
clearances.  
Compressor turns on and off frequently.  
-Save these instructions-  
The freezer has recently been disconnected for a  
period of time. 4 hours are required for the  
freezer to cool down completely.  
Temperature control is set too warm. Turn the  
control to a cooler setting and allow several hours  
for the temperature to stabilize. Door is kept open  
too long or is opened too frequently. Warm air  
enters the freezer every time the door is opened.  
Open the door less often.  
INSTALLATION INSTRUCTIONS  
Before Using Your Freezer  
Remove the exterior and interior packing.  
Check to be sure you have all of the following parts:  
1 Instruction Manual  
Temperature inside the freezer is too warm.  
Before connecting the freezer to the power source, let it stand upright for approximately 4 hours.  
This will reduce the possibility of a malfunction in the cooling system from improper handling  
during transportation.  
The door is not closed completely.  
The door gasket does not seal properly.  
A large amount of warm or hot food might have  
been stored recently. Wait until the freezer has  
had a chance to reach its selected temperature.  
The freezer has recently been disconnected for a  
period of time. 4 hours are required for the  
freezer to cool down completely.  
Clean the interior surface with lukewarm water using a soft cloth. (Cleaning instruction on page 6)  
Installing Your Freezer  
This appliance is designed to be free standing only, and should not be recessed or built-in.  
Place your freezer on a floor that is strong enoughto support the freezer when it is fully loaded.  
Allow 5 inches of space between the back and sides of the freezer, which allows the proper air  
ventilation. Adjust the feet to keep the freezer level.  
Locate the freezer away from di rect sunlight and sources of heat(stove, heater, radiator, etc.).  
Direct sunlight may affect the acrylic coating and heat sources may increase electrical  
consumption. Ambient temperature below 50°F or above 85°F will hinder the performance of this  
appliance. This unit is not designed for use in a garage or any other outside installation.  
Avoid locating the freezer in moist areas.  
Plug the freezer into dedicated, properly installed-grounded wall outlet. Do not under any  
circumstances cut or remove the third (ground) prong from the power cord. Any questions  
concerning power and/or grounding should be directed toward a certified electrician or an  
authorized service center. This unit is not designed to be installed in an RV or used with an  
inverter.  
Temperature inside the freezer is too cold.  
Temperature control is set too cold. Turn the  
control to a warmer setting and allow several  
hours for the temperature to stabilize.  
Temperature of external freezer surface is warm. The exterior freezer walls can be as much as  
30 F warmer than room temperature. This is  
normal while the compressor works to transfer  
heat from inside the freezer cabinet.  
Popping or cracking sound when compressor  
comes on.  
Metal parts undergo expansion and contraction,  
as in hot water pipes. This is normal. Sound will  
level off or disappear as freezer continues to run.  
Refrigerant (used to cool freezer) is circulating  
throughout the system. This is normal.  
Check to assure that the freezer is on a level  
surface.  
Floor is uneven or weak. Freezer rocks on the  
floor when it is moved slightly. Be sure floor can  
adequately support freezer. Level the freezer by  
putting wood or metal shims under part of the  
Bubbling or gurgling sound, like water boiling.  
Vibrations.  
After plugging the appliance into a wall outlet, allow the unit to cool down for 2~3 hours under  
before placing food in the freezer compartment.  
3
8
 
Electrical Connection  
CHANGING THE REVERSIBLE DOOR  
WARNING  
CAUTION: To avoid personal injury to yourself and/or property, we  
recommend someone assist you during the door reversal process.  
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is  
damaged, have it replaced by an authorized service center.  
This freezer should be properly grounded for your safety. The power cord of this freezer is equipped  
with a three-prong plug which mates with standard three prong wall out lets to minimize the possibility  
of electrical shock.  
The freezer has been built with the door hinges on the right. If you wish to change the opening direction,  
follow the instruction below:  
Note:  
Do not, under any circumstances, cut or remove the third ground prong from the power cord supplied.  
This freezer requires a standard 115/120 Volt A.C. ~/60Hz electrical outlet with three-prong ground.  
This freezer is not designed to be used with an inverter.  
• Unplug the freezer from its electrical outlet  
• Empty everything in the freezer, including all food items.  
• All parts removed during the process must be saved to reinstall the door.  
1. Remove the top hinge cover.  
2. Using Phillips Head Screwdriver, loosen and remove the screws holding the top hinge in place.  
3. Remove top hinge and carefully lift off the door.  
The cord should be secured behind the freezer and not left exposed or dangling to prevent accidental  
injury.  
4. Remove the screw hole plugs from the opposite side and insert the plugs in the screw hole openings  
of the just removed screws.  
Never unplug the freezer by pulling the power cord. Always grip the plug firmly and pull straight out  
from the receptacle.  
5. Remove any loose items in the refrigerator and carefully turn refrigerator on its back, remove both  
leveling legs and place in a secure area.  
Do not use an extension cord with this appliance. If the power cord is too short, have a qualified  
electrician or service technician install an outlet near the appliance. Use of an extension cord can  
negatively effect the performance of the unit.  
6. Loosen the screws holding the lower hinge bracket to the refrigerator and remove screws and  
bracket.  
7. Remove (2) screws from the other side and insert in the previously removed screw holes.  
8. Remove door pin by turning counter clockwise and reinsert to the underside of the bracket and  
tighten.  
OPERATING YOUR FREEZER  
9. Align bracket and insert (2) remaining screws into the holes provided .  
10. Align hole in the door with the door pin and washer and gently push down until firm.  
Temperature Control  
The thermostat control knob located in the right side regulates the temperature  
of the freezer compartment.  
The first time you turn the unit on, adjust thermostat control to required setting  
and run for at least 4 hours before putting frozen foods inside. This will ensure  
the cabinet is thoroughly chilled before food is put in.  
11. Align upper hinge bracket with screw holes insert screws and partially secure, check that door and  
cabinet are properly aligned and then secure tightly.  
12. Replace hinge cap.  
The range of the temperature control is from position "1" (cold) to "7" (coldest).  
Adjust the temperature control to the setting that best suits your needs.  
The setting of “4” should be appropriate for home or office freezer use.  
To adjust temperature to colder or warmer setting, please adjust the temperature control one numerical  
increment at a time.  
After each one numerical increment temperature adjustment, allow the freezer to operate at adjusted  
temperature for several hours for the freezer temperature to stabilize.  
To stop the freezer cooling process, turn the temperature control to "0". However, turning the temperature  
control to “0” position does not shut off the power to the freezer.  
7
4
 
NOTE;  
If the unit is unplugged or loses, you must wait 3 to 5 minutes before restarting the unit.  
CARE AND MAINTENANCE  
If you attempt to restart before this time delay, the freezer will not start.  
Large amounts of food will lower the cooling efficiency of the appliance.  
If you choose to change the thermostat setting, adjust thermostat control by one  
numerical increment at a time. Allow several hours for temperature to stabilize between  
adjustments.  
Cleaning Your Freezer  
Upon installation of your new appliance, it is recommended that it be cleaned thoroughly.  
Unplug the freezer, remove the food and storage basket.  
Wash the inside with a damp warm cloth soaked in lukewarm water and baking soda solution.  
The solution should be about 2 tablespoons of baking soda to a quart of water.  
Defrosting Your Freezer  
When? For the most efficient operation and minimum energy consumption, defrost the freezer  
when the frost on the freezer walls is excessive or ¼ to ½ inch thick.  
Choose a time when the stock of frozen food is low.  
Be sure to keep the door gasket (seal) clean to keep the unit running efficiently.  
The outside of the freezer should be clea ned with mild detergent and warm water.  
Dry the interior and exterior with a soft cloth.  
It is recommended that the unit be cleaned each time it is defrosted to help keep the unit odor free  
and running efficiently.  
CAUTION  
Do not use boiling water because it may damage the plastic parts. In addition, never  
use a sharp or metallic instrument to remove frost as it may damage the cooling coils  
and will void the warranty.  
Vacation Time  
Remove all the food.  
Unplug the freezer.  
Clean the freezer.  
Remove the frozen food from the freezer and place it in a cooler to protect the food.  
Unplug the appliance.  
Leave the door open slightly to avoid possible formation of condensation, mold, or odors.  
Use extreme caution in the case of children. The unit should not be accessible to child’s play.  
Short vacations: Leave the freezer operating during vacations of less than three weeks.  
Long vacations: If the appliance will not be used for several months, remove all food and unplug  
the power cord. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave  
the door open slightly: blocking it open if necessary or have the door removed.  
Open the freezer door.  
During defrosting, the ice melts into the cabinet. Place a suitable container to collect  
the defrosted water.  
Check the container occasionally so the water dose not overflow.  
After defrosting is completed, clean and thoroughly dry the interior of the freezer.  
Plug in the appliance and reset the thermostat to desired setting.  
Allow the cabinet to cool for 4 hours.  
Moving Your Freezer  
Unplug the freezer.  
Return food to the freezer.  
Remove all the food.  
Securely tape down all loose items inside your freezer.  
Tape the doors shut.  
Be sure the freezer stays in the upr ight position during transportation.  
HELPFUL HINT:  
Defrosting usually takes a few hours. Leaving the door open will help speed the  
process. Also, pouring warm water (not boiling) on the ice/frost will help speed  
melting.  
Energy Saving Tips  
The freezer should be located in the coolest area of the room, away from heat producing  
appliances or heating ducts, and out of the direct sunlight.  
Let hot foods cool to room temperature before placing in the freezer. Overloading the freezer  
forces the compressor to run longer. Foods that freeze too slowly may lose quality, or spoil.  
Be sure to wrap foods properly, and wipe containersdry before placing them in the freezer. This  
cuts down on frost build-up inside the freezer.  
WARNING  
Scraping ice from the freezer compartment can damage the unit.  
Freezer should not be lined with aluminum foil, wax paper, or paper toweling. Liners interfere  
with cold air circulation, making the freezer less efficient.  
Organize and label food to reduce door openings and extended searches. Remove as many  
items as needed at one time, and close the door as soon as possible.  
5
6
 

Sharp DVD VCR Combo DV RW550U User Manual
Shaw Universal Remote ATLAS PVR Universal Remote Control User Manual
Shindaiwa Trimmer AH254 User Manual
Sony Camcorder 510P User Manual
Sony Car Stereo System XR C7500R User Manual
Sony TV Video Accessories TDG BR200 User Manual
Sunbeam Juicer JE8500 User Manual
Swann Security Camera SW C DPCC User Manual
Sylvania Portable DVD Player SDVD7024 User Manual
Tapco DJ Equipment MIX10FXP User Manual