Sunbeam Kitchen Utensil EK3800 User Manual

Carveasy  
Electric Knife  
Instruction Booklet  
This book covers the use and care of the following Sunbeam Electric Knives:  
EK3800 Sunbeam Carveasy  
EK5600 Sunbeam Carveasy Pro  
Please read these instructions carefully  
and retain for future reference.  
EK5600  
EK3800  
 
Sunbeam’s Safety Precautions  
SAFETY PRECAUTIONS FOR YOUR  
SUNBEAM ELECTRIC KNIFE.  
• Serrated edges of the blades are very sharp.  
• Do not allow children to play with blades.  
• Caution is necessary when handling the blades.  
Sunbeam is very safety conscious when  
designing and manufacturing consumer products,  
but it is essential that the product user also  
exercise care when using an electrical appliance.  
Listed below are precautions which are essential  
for the safe use of an electrical appliance:  
• Read carefully and save all the instructions  
provided with an appliance.  
• Do not use an appliance for any purpose  
other than its intended use.  
• Do not place an appliance on or near a hot gas  
flame, electric element or on a heated oven.  
• Do not place on top of any other appliance.  
• Do not let the power cord of an appliance hang  
over the edge of a table or bench top or touch  
any hot surface.  
• Always turn the power off at the power outlet  
before you insert or remove a plug. Remove  
by grasping the plug - do not pull on the cord.  
Turn the power off and remove the plug  
when the appliance is not in use and  
before cleaning.  
• Do not use your appliance with an extension  
cord unless this cord has been checked  
and tested by a qualified technician or  
service person.  
• Always use your appliance from a power  
outlet of the voltage (A.C. only) marked  
on the appliance.  
• This appliance is not intended for use by  
persons (including children) with reduced  
physical, sensory or mental capabilities, or  
lack of experience and knowledge, unless they  
have been given supervision or instruction  
concerning use of the appliance by a person  
responsible for their safety.  
• Do not operate any electrical appliance with  
a damaged cord or after the appliance has  
been damaged in any manner. If damage is  
suspected, return the appliance to the nearest  
Sunbeam Appointed Service Centre  
for examination, repair or adjustment.  
• For additional protection, Sunbeam  
recommend the use of a residual current  
device (RCD) with a tripping current not  
exceeding 30mA in the electrical circuit  
supplying power to your appliances.  
• Do not immerse the appliance in water  
or any other liquid unless recommended.  
• Appliances are not intended to be operated  
by means of an external timer or separate  
remote control system.  
• This appliance is intended to be used in  
household and similar applications such  
as: staff kitchen areas in shops, offices and  
other working environments; farm houses; by  
clients in hotels, motels and other residential  
type environments; bed and breakfast type  
environments.  
• Children should be supervised to ensure that  
they do not play with the appliance.  
• The temperature of accessible surfaces may be  
high when the appliance is operating.  
• Never leave an appliance unattended while  
in use.  
If you have any concerns regarding the performance and use of your appliance,  
Ensure the above safety precautions are understood.  
1
 
Features of your Sunbeam  
Carveasy Pro  
Blade release button  
Soft touch ergonomic handle  
Extra long stainless steel blades  
Double movement  
safety trigger  
Neon power light  
Handy hang up loop  
EK5600 Pictured  
Micro serrated stainless steel blades  
Handle  
Serrated stainless steel blades are durable  
and sharp for efficient slicing and carving.  
Convenient and simple to operate. The  
ergonomic design provides comfort, versatility  
and control when carving both vertically and  
horizontally.  
Blade release button  
Conveniently located at the top of the handle  
for thumb action release of the stainless steel  
blades.  
Handy hang up loop  
The handy hang-up loop enables the product  
to be stored conveniently for easy access any  
time.  
Double movement safety trigger  
Located under the handle for ease of  
operation, the index-finger trigger action,  
allowing the most comfortable position for  
carving. The double movement trigger system  
provides added safety.  
Safety guards  
For safe fitting and removal of blades  
Neon power light  
The neon power light indicates when the  
Carveasy Prois plugged in and switched on.  
2
 
Features of your Sunbeam  
Carveasy  
Blade release button  
Soft touch ergonomic handle  
Extra long stainless steel blades  
Double movement  
safety trigger  
Neon power light  
Handy hang up loop  
EK3800 Pictured  
Micro serrated stainless steel blades  
Handle  
Serrated stainless steel blades are durable  
and sharp for efficient slicing and carving.  
Convenient and simple to operate. The  
ergonomic design provides comfort, versatility  
and control when carving both vertically and  
horizontally.  
Blade release button  
Conveniently located at the top of the handle  
for thumb action release of the stainless steel  
blades.  
Handy hang up loop  
The handy hang-up loop enables the product  
to be stored conveniently for easy access any  
time.  
Double movement safety trigger  
Located under the handle for ease of  
operation, the index-finger trigger action,  
allowing the most comfortable position for  
carving. The double movement trigger system  
provides added safety.  
Safety guards  
For safe fitting and removal of blades  
Neon power light  
The neon power light indicates when the  
Carveasyis plugged in and switched on.  
3
 
Using your Sunbeam Knife  
1.Interlock blades together before inserting  
into the appliance. To assemble blades,  
grasp shaft ends below the safety guards  
and slip the rivet on the tip of the other  
blade. See Figure 1. Bring blades together  
ensuring tips remain together.  
under the handle to activate the motor.  
Releasing the switch will automatically  
stop the motor.  
Warning: Avoid contact with moving parts.  
Keep hands, hair, clothing and other utensils  
away from moving blades during operation to  
prevent personal injury and/or damage to the  
knife.  
Note: Always use both blades when operating  
the Carveasyand the CarveasyPro.  
4.When slicing is completed, turn the power  
off at the power outlet and remove the  
plug. Slide back the Blade Release, hold  
the blades by the safety guards with the  
cutting edge facing downward and pull the  
blades out of the slots. See Figure 3.  
Figure 1  
2.Hold assembled blades by the safety  
guards and slide shafts gently into the  
blade slot until clipped into position.  
See Figure 2.  
Warning: Only when blades are fitted should  
the cord be connected to the  
power outlet.  
Figure 3  
Warning: The blades of your Sunbeam  
Carveasyand CarveasyPro are sharp!  
Handle with extreme care. We recommend  
using the guard sleeve provided when  
handling the blades. Do not fit or remove  
blades whilst the knife is connected to  
the power outlet. Do not allow children to  
operate the appliance.  
Figure 2  
3.Insert the plug into a 230-240 volt (AC  
only) power outlet and ensure the cord is  
well away from the blades. Holding the  
knife with one hand, slide and press the  
double movement safety trigger positioned  
4
 
Slicing Hints  
Always place food to be sliced on a wooden  
or plastic cutting board. Do not slice food  
on china; metal or bench tops, as scratching  
may occur. Guide blades through food.  
A sawing action is not necessary. Do not  
force blades through food. To maintain the  
sharpness of blades, do not cut through  
bones, fruit pips or stones or any other hard  
substances.  
Before carving meat or chicken, remove  
skewers. If desired, string may be left around  
the meat whilst carving. The use of a carving  
fork to steady the meat assists in carving  
straight, even slices. Do not attempt to  
sharpen blades.  
We recommend when slicing foods like bread,  
a light smear of cooking oil, margarine or  
similar, on the inside of the blades will  
reduce the friction.  
For best results when carving meat and  
poultry allow cooked meat to stand for 10-15  
minutes before slicing. this allows the juices  
to set and makes carving easier and neater.  
5
 
Care and Cleaning  
pads or powders on blades. After cleaning,  
always store blades in plastic sleeves. To  
clean motor housing wipe with a soft damp  
cloth.  
Before storing your knife, a light smear of  
cooking oil or similar on the inside of the  
blade is suggested.  
Warning: Ensure the unit is switched off  
and the plug removed from the power outlet  
before removing the blades and/or cleaning.  
Unlock the blades by sliding apart. Always  
hold blades by the shaft end, behind the  
safety guard, when handling and cleaning.  
Wash the blades in hot soapy water with a  
soft cloth or sponge. Rinse thoroughly and  
dry completely. Do not use abrasive scouring  
6
 
Notes  
 
Notes  
 
12 Month Replacement Guarantee  
In the unlikely event that this appliance develops any malfunction  
within 12 months of purchase (3 months commercial use) due to  
faulty materials or manufacture, we will replace it for you  
free of charge.  
Should you experience any difficulties with  
your appliance, please phone our customer  
service line for advice on 1300 881 861 in  
Australia, or 0800 786 232 in New Zealand.  
Alternatively, you can send a written claim  
to Sunbeam at the address listed below.  
On receipt of your claim, Sunbeam will  
seek to resolve your difficulties or, if the  
appliance is defective, advise you on how  
to obtain a replacement or refund.  
In Australia you are entitled to a  
replacement or refund for a major failure and  
for compensation for any other reasonably  
foreseeable loss or damage. You are also  
entitled to have the goods repaired or  
replaced if the goods fail to be of acceptable  
quality and the failure does not amount to  
a major failure.  
Should your appliance require repair or  
service after the guarantee period, contact  
your nearest Sunbeam service centre.  
Your Sunbeam 12 Month Replacement  
Guarantee naturally does not cover misuse  
or negligent handling and normal wear and  
tear.  
For a complete list of Sunbeam’s authorised  
service centres visit our website or call:  
Australia  
Similarly your 12 Month Replacement  
Guarantee does not cover freight or any other  
costs incurred in making a claim. Please  
retain your receipt as proof of purchase.  
1300 881 861  
Units 5 & 6, 13 Lord Street  
Botany NSW 2019 Australia  
The benefits given to you by this guarantee  
are in addition to your other rights and  
remedies under any laws which relate to the  
appliance.  
New Zealand  
0800 786 232  
26 Vestey Drive, Mt Wellington  
Auckland, New Zealand  
Our goods come with guarantees that cannot  
be excluded under the Australian Consumer  
Law and under the New Zealand Consumer  
Guarantees Act.  
 
Need help with your appliance?  
Contact our customer service team or visit  
our website for information and tips on  
getting the most from your appliance.  
In Australia  
Or call 1300 881 861  
In New Zealand  
Or call 0800 786 232  
is a registered trademark.  
‘Carveasy’ is a trademark of Sunbeam Corporation.  
Made in China.  
Due to minor changes in design or otherwise,  
the product may differ from the one shown in this leaflet.  
© Copyright. Sunbeam Corporation Limited 2011.  
ABN 45 000 006 771  
Units 5 & 6, 13 Lord Street  
Botany NSW 2019 Australia  
Unit 3, Building D  
26 Vestey Drive  
Mt Wellington Auckland  
New Zealand  
Sunbeam Corporation is a division of GUD Holdings Ltd.  
9/12  
 

Sharp Air Cleaner FZC150HFU User Manual
Sharp Microwave Oven R 980J User Manual
Sierra Monitor Corporation Carbon Monoxide Alarm 2001 User Manual
Sierra Wireless Modem 2120028 User Manual
Silvercrest Coffeemaker SEM 1100 A1 User Manual
Snapper Automobile Accessories 1693754 User Manual
Soundstream Technologies Portable Speaker SPL 60 User Manual
Standard Horizon Recording Equipment 24 96 User Manual
State Industries Electric Heater GPO69 700 User Manual
Targus Computer Drive PACD010 400 0137 001B User Manual