Sylvania TV VCR Combo 63134C User Manual

OWNER’S  
MANUAL  
COLOR TV/VCR  
63134C (13 inch)  
63194C (19 inch)  
This Owner’s Manual is made of  
recycled paper.  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
energy efficiency. ENERGY STAR® is  
a U.S. registered mark.  
If you need additional assistance for set-up or operating  
after reading owner’s manual, please call  
TOLL FREE : 1-800-968-3429  
 
Please read before using this equipment  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/VCR, be sure the  
antenna or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
19.Damage Requiring Service-Unplug this TV/VCR from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/VCR.  
c. If the TV/VCR has been exposed to rain or water.  
d. If the TV/VCR does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper adjust-  
ment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the TV/VCR to its normal operation.  
14.Lightning-For added protection for this TV/VCR receiver  
during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the TV/VCR due to lightning and  
power-line surges.  
e. If the TV/VCR has been dropped or damaged in any way.  
f. When the TV/VCR exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
21.Safety Check-Upon completion of any service or repairs to  
this TV/VCR, ask the service technician to perform routine  
safety checks to determine that the TV/VCR is in proper  
operating condition.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/VCR through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the TV/VCR.  
22.Heat-This TV/VCR product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
18.Servicing-Do not attempt to service this TV/VCR yourself  
as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to quali-  
fied service personnel.  
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.  
Download from Www.Somanuals.com- 3. A-ll Manuals Search And Download.  
EN  
9I03  
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LOCATION  
For safe operation and satisfactory performance of  
your TV/VCR, keep the following in mind when  
selecting a place for its installation:  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top and bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
Unauthorized recording or use of broadcast televi-  
sion programming, video tape, film or other copy-  
righted material may violate applicable copyright  
laws. We assume no responsibility for the unautho-  
rized duplication, use, or other acts which infringe  
upon the rights of copyright owners.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/VCR near strong magnetic fields.  
Avoid moving TV/VCR to locations where temper-  
ature differences are extreme.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If, by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to an  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/VCR cassette holder.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place,  
or after heating a cold room or under conditions of  
high humidity. If a tape is played in a TV/VCR  
which has moisture, it may damage the tape and  
TV/VCR. Therefore if condensation occurs inside the  
unit, turn the POWER button on and allow at least 2  
hours for the unit to dry out.  
3) Connect the equipment to an outlet on a circuit  
different from that to which the receiver is con-  
nected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
Download from Www.Somanuals.co-m4. A-ll Manuals Search And Download.  
EN  
9I03  
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6  
C OPERATING CONTROLS AND FUNCTIONS 7  
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20  
NORMAL RECORDING . . . . . . . . . . . . . . . . .20  
OTR (One Touch Recording) . . . . . . . . . . . . . .21  
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21  
TIMER PROGRAM EXTENSION . . . . . . . . .22  
HINTS FOR AUTOMATIC TIMER  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23  
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9  
ANTENNA/CABLE CONNECTIONS . . . . . . .9  
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10  
INSTALLING THE BATTERIES . . . . . . . . . . .10  
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23  
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24  
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10  
CHANNEL SET UP FOR THE FIRST TIME .10  
CLOCK SET UP (AUTO / MANUAL) . . . . . .11  
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .12  
DELETING (OR ADDING) CHANNEL . . . . .12  
SELECTING THE LANGUAGE . . . . . . . . . . .13  
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13  
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25  
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25  
REAL TIME TAPE COUNTER . . . . . . . . . . . .25  
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27  
C CABLE CHANNEL DESIGNATIONS . . . . . .27  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14  
WATCHING A TV PROGRAM . . . . . . . . . . . .14  
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14  
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15  
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .18  
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .19  
RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .19  
VERTICAL HOLD CONTROL . . . . . . . . . . . .20  
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .20  
TRACKING ADJUSTMENT . . . . . . . . . . . . . .20  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
Download from Www.Somanuals.com- 5. A-ll Manuals Search And Download.  
EN  
9I03  
FEATURES  
Rotary 4-head Record/Playback System–Four  
heads ensure excellent picture quality and special  
effects playback.  
Index Search–Fast-forwards to start of next recording.  
Slow Motion–View recorded program at slower  
than normal speed.  
Infrared remote control  
Bilingual on screen menu display selectable in  
English or Spanish  
Auto Head Cleaner–Automatically cleans video  
heads as you insert or remove a cassette.  
Zero Return–The tape returns to counter of  
0:00:00 by rewinding or fast forwarding.  
Still–“Freeze” the picture at any time, for close  
viewing of a particular scene. Only tapes recorded  
in SLP mode will show a fairly clear picture.  
Digital Auto Tracking (DTR)–Automatically  
adjusts the tracking for each tape you play.  
Rental play mode–Improves playback picture  
quality from worn tapes, such as rental tapes.  
Auto repeat–Allows you to repeat the playing of a  
tape indefinitely without pressing the PLAY button.  
Time search–Lets you set the TV/VCR to advance  
the tape by entering the desired playback time you  
want to skip.  
Real time counter–This shows the elapsed record-  
ing or playback time in hours, minutes, and sec-  
onds. The “–” indication will appear when the tape  
is rewound further than the tape counter position  
“0:00:00”.  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call–(A converter may  
be necessary to view scrambled cable channels.)  
Auto Clock Setting–Allows you to set the clock  
from a PBS broadcast station.  
Closed caption system–You may view specially  
labeled (cc) TV programs, movies, news, prere-  
corded tapes, etc. with either a dialogue caption or  
text display added to the program.  
Game mode–Automatically sets external input  
mode and allows the TV/VCR display to be suit-  
able for use with TV games.  
Auto power on and off system–Automatically  
turns on the TV/VCR when you insert the cassette,  
turns off after auto-rewind, and ejects when the  
beginning of the tape is reached.  
Auto rewind when the end of a tape is  
reached–This function doesn’t occur when using  
timer recording.  
2 Step picture search operation–You can view a  
video program at a high speed or super high speed  
in either a forward or reverse direction in LP and  
SLP mode. For SP mode only high speed.  
Three different playback tape speeds : SP/LP/SLP  
Two different recording tape speeds : SP/SLP  
OTR (One Touch Recording)–Instant timed  
recording from 30 to 480 minutes is possible at the  
push of the REC/OTR button.  
1 Year, 8 events (including Daily and Weekly  
Timer Recording)–The built-in timer allows you to  
record up to 8 programs at different times on dif-  
ferent channels up to 1 year in advance. The Daily  
timer allows recordings to be made of daily broad-  
casts, and the Weekly timer allows recording to be  
made once a week up to the end of the tape.  
Auto return–After timer recording is finished, the  
TV/VCR can return to the beginning of the record-  
ing.  
Wake-up/Sleep timer–Allows you to have the  
TV/VCR automatically turn on or off at a desired  
time.  
Timer Program Extension–Allow you to shift the  
time schedule for automatic timer recording.  
V-CHIP–Enables parents to prevent their children  
from watching inappropriate material on TV.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
PART NO. (NO146UD)  
2 AA Batteries  
Rod Antenna (13” model only)  
PART NO. (0EMN00673 or  
0EMN01599 or0EMN01755)  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-  
968-3429.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control. If you decide to use a universal remote control with this unit, please be aware  
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-  
versal remote control.  
Download from Www.Somanuals.co-m6. A-ll Manuals Search And Download.  
EN  
9I03  
OPERATING CONTROLS AND FUNCTIONS  
"
"
This manual covers 13 and 19 . The operation of the two models are exactly the same except the  
"
appearance. 19 model is illustrated in this manual.  
- TV/VCR FRONT PANEL -  
VIDEO AUDIO  
POWER  
CHANNEL  
STOP/EJECT  
REW PLAY F.FWD  
REC/OTR EARPHONE  
VOLUME  
13  
1 2 3 4 5 6 7 8 9101112  
14  
- REMOTE CONTROL -  
1 VIDEO input jack– Connect to the video output  
jack of your video camera or another VCR.  
2 AUDIO input jack– Connect to the audio output  
jack of your audio equipment, video camera or  
another VCR.  
25  
26  
24  
WAKE-UP  
/SLEEP  
POWER  
EJECT  
3
CHANNEL  
RETURN  
3 POWER button– Press to turn TV/VCR on and  
off. Press to activate timer recording.  
1
4
7
2
5
8
3
6
9
15  
4
VOLUME X / Y buttons– Adjust the volume level.  
CHANNEL  
VOLUME  
5
4
5 CHANNEL K / L buttons– Press to select the  
desired channels for viewing or recording.  
You may display the main menu on the TV screen  
by pressing repeatedly this button on the TV/VCR.  
TRACKING function– Press to minimize video  
‘noise’ (lines or dots on screen) during playback or  
Slow mode. (See page 20.)  
6 Remote Sensor Window– Receives the infrared  
signals from the remote control.  
7 STOP button– Press to stop the tape motion.  
EJECT button– Press in the Stop mode to remove  
tape from TV/VCR.  
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
23  
9
PLAY  
10  
REW  
F.FWD  
STOP  
7
SPEED PAUSE/STILL  
RECORD  
22  
21  
11  
18  
T-PROG.  
CLEAR  
GAME  
SLOW  
COUNTER  
RESET  
19  
20  
L button–  
Press to select setting modes from the on screen  
menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
8 REW button– Press to rewind the tape, or to view  
the picture rapidly in reverse during playback  
mode. (Rewind Search)  
s button–  
Press to select a mode from a particular menu.  
(for example: LANGUAGE or USER’S SET UP)  
Download from Www.Somanuals.com- 7. A-ll Manuals Search And Download.  
EN  
9I03  
- REAR VIEW -*  
ANT.  
27  
28  
18 SPEED button– Press to choose the desired  
recording speed:SP/SLP.  
9 PLAY button– Press to begin playback.  
K button–  
19 T-PROG. CLEAR button– Press to cancel a setting  
of timer program. (See page 23.)  
Press to select setting modes from the on screen  
menu.  
COUNTER RESET button– Press to reset counter  
to 0:00:00.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
10 F.FWD button– Press to rapidly advance the tape,  
or to view the picture rapidly in forward during  
playback mode. (Forward Search)  
20 GAME button– Sets the game mode and external  
input mode at the same time. (See page 14.)  
21 SLOW button– Press to start slow motion playback.  
22 PAUSE/STILL button– Press to temporarily stop  
the tape during the recording or to view a still pic-  
ture during playback.  
Frame Advance function– Press to advance the  
picture one frame at a time during Still mode.  
23 MUTE button– Mutes the sound. Press it again to  
resume sound.  
24 CHANNEL RETURN button– Press to go back to  
the previously viewed channel. For example,  
pressing this button once will change channel dis-  
play from 3 (present channel) to 10 (previously  
viewed channel), and pressing it a second time  
will return from 10 to 3.  
25 WAKE UP/SLEEP button– Sets the Wake up or  
Sleep Timer. (See page 23 and 24.)  
26 EJECT button– Press in the Stop mode to remove  
a tape from the TV/VCR.  
27 Power cord– Connect to a standard AC outlet  
(120V/60Hz).  
28 ANT. terminal– Connect to an antenna or cable  
system.  
B button–  
When setting program (for example: setting clock  
or timer program), press to determine your selec-  
tion and proceed to the next step you want to input.  
Press to determine setting modes from on screen  
menu.  
Press to select a mode from a particular menu.  
(for example: LANGUAGE or USER’S SET UP)  
11 REC button– Press for manual recording.  
OTR button– Activates One Touch Recording.  
(only on the TV/VCR)  
12 RECORD indicator– Flashes during recording.  
Lights up in the Stand-by mode for Timer Recording.  
13 EARPHONE jack– Connects to earphones (not  
supplied) for personal listening. The size of jack is  
1/8” monaural (3.5mm).  
14 Cassette compartment  
15 Number buttons– Press to select desired channels  
for viewing or recording. To select channels from  
1 to 9, first press the 0 button and then 1 to 9.  
+100 button– When selecting cable channels which  
are higher than 99, press this button first, then press  
the last two digits. (To select channel 125, first press  
the “+100” button then press “2” and “5”).  
16 MENU button– Press to display the main menu on  
the TV screen.  
17 DISPLAY button– Display the counter or the cur-  
rent channel number and current time on the TV  
screen. (See page 25.)  
Download from Www.Somanuals.co-m8. A-ll Manuals Search And Download.  
EN  
9I03  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
From Cable System or  
Satellite Dish  
VHF/UHF Antenna  
(Not supplied)  
Satellite Box or  
Cable Box  
(Not supplied)  
Rod Antenna  
(Supplied with 13” model only)  
OUT  
IN  
VHF Antenna  
(Not supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
or  
VHF/UHF  
Combiner  
(Not supplied)  
or  
ANT.  
or  
75-ohm Coaxial  
Cable (Not supplied)  
Flat twin-lead cable  
or  
VHF/UHF COMBINED ANTENNA  
VHF/UHF SEPARATE ANTENNAS  
The VHF/UHF Rod Antenna (supplied with 13”  
model only) is detachable. Insert the stem of the  
antenna into the hole on the upper-back portion of  
the TV/VCR.Connect the VHF/UHF Rod Antenna or  
VHF/UHF Combination Antenna to the ANT. termi-  
nal of the TV/VCR as shown in the diagram. For the  
best reception, fully extend the VHF/UHF Rod  
Antenna and make the necessary adjustments. (Avoid  
touching the top section when adjusting.)  
NOTE:  
In some areas it will be necessary to use an outdoor  
antenna.  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your TV/VCR without a converter box.  
By using this connection you can:  
1) Use the TV/VCR remote to select channels.  
2) Program one or more unscrambled channels for  
Automatic Timer Recording.  
NOTE: This unit will ONLY record and view the  
same channel.  
Before plugging the Rod antenna into antenna termi-  
nal, check that the pin is not bent. If it is bent,  
straighten the pin as illustrated, then plug the pin into  
antenna terminal.  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE  
BOX  
Bent pin  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown in the diagram.  
By using this connection you can also record scram-  
bled channels. However, channel selection must be  
made with the converter box or satellite box. This  
means that channels cannot be changed using the  
TV/VCR Remote Control. Unattended timer record-  
ing is limited to one channel at a time.  
Cable Plug  
(Straight pin)  
(Needs to be straightened)  
NOTE:  
The connection of an indoor antenna may not always  
give acceptable TV reception.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
Download from Www.Somanuals.com- 9. A-ll Manuals Search And Download.  
EN  
9I03  
TO RECORD A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
INSTALLING THE BATTERIES  
1) Set the TV/VCR channel selector to the output  
channel of the Cable Converter Box or Satellite  
Box. (Example: CH3)  
2) Select the channel to record from your Cable  
Converter Box or Satellite Box.  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
3)Replace the cover.  
EXTERNAL INPUT MODE  
When using an external input signal (another VCR or  
video camera), connect the player’s audio/video out-  
put cables to the AUDIO IN/ VIDEO IN jacks of  
your TV/VCR. Then press the CHANNEL K or  
button until “AUX” appears on the screen.  
NOTE: “AUX” is found below the  
lowest memorized channel.  
L
AUX  
(Example: CH2)  
SET UP FOR USE  
You can program the tuner to scan all the channels you receive in your area.  
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just  
select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then  
select the channel to be viewed on the Cable Box or Satellite Box.  
CHANNEL SET UP FOR THE  
4 Begin auto preset  
– SET UP –  
FIRST TIME  
Press the PLAY/K or STOP/L but-  
LANGUAGE  
[ENGLISH] ESPAÑOL  
ton to point to “AUTO PRESET”.  
1 Plug in the TV/VCR power cord  
B
AUTO PRESET  
Then press the F.FWD/B button.  
The tuner scans and memorizes all  
active channels in your area.  
NOTES:  
The TV/VCR distinguishes between standard TV  
channels and cable channels.  
If you want to play or record a video tape  
BEFORE presetting the tuner, you must press the  
MENU button on the remote control. To preset the  
tuner again, see “CHANNEL SET UP AGAIN” on  
page 12.  
Plug the TV/VCR power cord into a  
standard AC outlet.  
NOTE:  
If some digits appear in the corner of  
the screen, press the POWER button  
without unplugging the power cord.  
2 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR  
The TV/VCR may memorize TV channels as  
CATV channels if reception conditions are poor. If  
this happens, try the AUTO MEMO action again  
when reception conditions are better.  
3 Select “ENGLISH” or “ESPAÑOL”  
Select “ENGLISH” or  
– SET UP –  
“ESPAÑOL”=Spanish using the  
B
LANGUAGE  
[ENGLISH] ESPAÑOL  
F.FWD/B or REW/s button. “[ ]”  
indicate the selected language.  
AUTO PRESET  
5 After scanning  
The tuner stops on the lowest memorized channel.  
If you want to recall the selected channels, you can  
select the desired channel directly with the remote  
control number buttons or CHANNEL K or L button.  
- 10 -  
EN  
9I03  
 
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “SETTING  
CLOCK”.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
TO SELECT A DESIRED CHANNEL  
You can select the desired channel by using the  
CHANNEL K or L button or directly pressing the  
number buttons on the remote control.  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
Note for using the number buttons:  
Then, press the F.FWD/B button.  
When selecting cable channels which are higher  
than 99, press the +100 button first, then, press the  
last two digits. (Example: to select channel 125,  
first press the +100 button then press “2” and “5”).  
– SETTING CLOCK –  
2 Set “AUTO CLOCK” to [ON]  
Press the F.FWD/B or REW/s  
button repeatedly until [ON]  
appears.  
B
AUTO CLOCK  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
[AUTO]  
You must proceed single-digit channel numbers  
with a zero (Example: 02 ... 09).  
[OFF]  
CLOCK SET UP  
3 Enter the channel number for the PBS station  
(AUTO / MANUAL)  
Press the PLAY/K or STOP/L but-  
– SETTING CLOCK –  
ton to point to “AUTO CLOCK  
CH”.  
Then press the F.FWD/B or  
REW/s button until the channel  
number for your local PBS station  
appears.  
Set the clock accurately for proper automatic timer  
recording. If the Public Broadcasting Station (PBS)  
is available in your area, follow “AUTO CLOCK  
SETTING”. If it is not, follow “MANUAL CLOCK  
SETTING”.  
AUTO CLOCK  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
B
[AUTO]  
[OFF]  
If you do not know the PBS channel number, leave it  
set to [AUTO] which is located before [2]. The  
TV/VCR will search automatically all available chan-  
nels for the local PBS station, and will select that  
channel.  
AUTO CLOCK SETTING  
You can have the TV/VCR set the clock automatical-  
ly by using the Public Broadcasting Station (PBS)  
channel in your area. Once you have set the clock by  
using the following procedure, the TV/VCR will  
automatically monitor the correct time and date  
being broadcast by the PBS station in your area,  
using a new service called Extended Data Service  
(XDS).  
4 Exit the Auto Clock Setting  
Press the MENU button on the remote control to  
return to TV mode.  
Make sure ...  
5 Turn off the TV/VCR  
Turn the TV/VCR off. The Auto Clock functions  
automatically while the TV/VCR is off.  
TV/VCR power must be turned on.  
Confirm that the antenna connections are correct.  
The cable converter box must be turned on if your  
TV/VCR is connected directly to it. (See NOTES:)  
If you choose [AUTO],  
The TV/VCR must search until the PBS channel is  
found. It must scan each channel for a couple of  
seconds to determine if that channel is transmitting  
the XDS signal.  
The channel is properly set in advance.  
NOTES:  
Auto clock setting only needs to be set once. But it  
can be done again if the clock’s time has become  
incorrect for some reason.  
If the time that is automatically set by this selected  
PBS station is incorrect, it may not be your local  
PBS station, but one from a different time zone.  
Or if no channel is broadcasting the XDS signal in  
your area, no time will show. In these cases, you  
must manually enter the correct local PBS station,  
or set the clock manually and turn off the Auto  
Clock Setting feature.  
If the TV/VCR is connected directly to a cable  
converter box or satellite box, the local PBS station  
must be selected on the cable box itself, and the  
TV/VCR must be set to the output channel of the  
cable converter box or satellite box (usually chan-  
nel 3 or 4), to be able to set up or correct the clock  
automatically.  
MANUAL CLOCK SETTING  
Make sure ...  
TV/VCR power must be turned on.  
In the example below, the clock is to be set to:  
If you do not know what your local PBS station is,  
then follow “Manual Clock Settings”.  
The TV/VCR cannot control the channels of the  
cable converter box or satellite box.  
DATE  
May 7th, 2002  
SETTING TIME 5:40PM  
- 11 -  
EN  
9I03  
 
NOTE:  
When unplugging the AC cord or if there is a power  
failure for more than 3 seconds, you may have to  
reset the clock.  
– M E N U –  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control. Press the PLAY/K  
or STOP/L button to point to “SET-  
TING CLOCK”.  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
TO CHANGE CLOCK SETTING  
INDEX SEARCH  
If you want to change the clock,  
1)Follow steps [1] and [2].  
Then, press the F.FWD/B button.  
2)Select where you want to change using the  
F.FWD/B or REW/s button.  
3)Enter correct numbers using the PLAY/K or  
STOP/L button.  
4)Press the MENU button on the remote control to  
start the clock.  
– SETTING CLOCK –  
2 Select “MANUAL CLOCK  
AUTO CLOCK  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
SET”  
[AUTO]  
[OFF]  
B
Press the PLAY/K or STOP/L but-  
ton to point to “MANUAL CLOCK  
SET”.  
Then, press the F.FWD/B button.  
PLEASE NOTE:  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and press  
the F.FWD/B or REW/s button to turn [OFF] this  
function. Then you can manually adjust the clock.  
3 Select the month  
Press the PLAY/K or STOP/L but-  
ton until your desired month  
appears. (Example: May 05)  
Then, press the F.FWD/B button.  
0 5  
/
– – – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
:
CHANNEL SET UP AGAIN  
Make sure ...  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
4 Select the day  
Press the PLAY/K or STOP/L but-  
ton until your desired day appears.  
(Example: 7th 07)  
Press the POWER button to turn on the TV/VCR.  
0 5  
/
0 7 – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
:
1 Select “CHANNEL SET UP”  
Then, press the F.FWD/B button.  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
remote control.  
B
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
5 Select the year  
Press the PLAY/K or STOP/L but-  
ton until your desired year appears.  
(Example: 2002)  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
0 5  
/
0 7 TUE 2 0 0 2  
TIME SEARCH  
INDEX SEARCH  
HOUR  
– –  
MINUTE  
– – – –  
:
Then, press the F.FWD/B button.  
Then, press the F.FWD/B button.  
2 Begin auto preset  
– CHANNEL SET UP –  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
6 Select the hour  
Press the PLAY/K or STOP/L but-  
ton until your desired hour appears.  
(Example: 5, PM)  
ADD / DELETE CH (TV)  
AUTO PRESET  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO PRESET”.  
Then, press the F.FWD/B button.  
The tuner scans and memorizes all  
the active channels in your area.  
B
0 5  
/
0 7 TUE 2 0 0 2  
HOUR  
0 5  
MINUTE  
– – PM  
:
Then, press the F.FWD/B button.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
7 Select the minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: 40)  
3 After scanning  
The tuner stops on the lowest memorized channel.  
0 5  
/
0 7 TUE 2 0 0 2  
HOUR  
0 5  
MINUTE  
4 0 PM  
:
DELETING (OR ADDING)  
CHANNEL  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you  
can add the deleted channel into the memory again.)  
5:40 PM  
8 Start the clock  
Press the MENU button on the  
remote control.  
Although seconds are not displayed,  
they begin counting from 00 when  
you press the MENU button on the remote control.  
Use this feature to synchronize the clock with the  
correct time.  
- 12 -  
EN  
9I03  
 
1 Select “CHANNEL SET UP”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
2 Select “ENGLISH” or “ESPAÑOL”  
Select “ENGLISH” or “ESPAÑOL”= Spanish using  
the F.FWD/B or REW/s button.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
3 Exit the Language mode  
Press the MENU button on the remote control to  
return to TV mode.  
TIME SEARCH  
INDEX SEARCH  
Then, press the F.FWD/B button.  
NOTE: If for some reason the menu is in Spanish,  
press the MENU button on the remote control, press  
the PLAY/K button to point to “IDIOMA  
[ESPAÑOL]”, then press the F.FWD/B button, then  
press the MENU button on the remote control.  
– CHANNEL SET UP –  
2 Select “ADD/DELETE CH”  
Press the PLAY/K or STOP/L but-  
ton to point to “ADD/DELETE  
CH”.  
B
ADD / DELETE CH (TV)  
AUTO PRESET  
Press the F.FWD/B button.  
DAYLIGHT-SAVING TIME  
Select this feature and the TV/VCR’s clock automati-  
cally will advance one hour in April, then reverse one  
hour in October.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
First Sunday of April : At 2 AM the clock imme-  
3 Enter the desired channel number  
Press the PLAY/K or STOP/L but-  
ton until your desired channel num-  
ber appears. (You can also use the  
number buttons or the CHANNEL  
K/L button to enter it.) (Example:  
CH8)  
08  
ADD / DELETE  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM  
will not record.  
4 Delete (or add) it from (into) memory  
Press the F.FWD/B or REW/s button. The channel  
number changes to light red. The channel is deleted  
from memory.  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
To delete another channel, repeat steps [3] and [4].  
If you press the F.FWD/B or REW/s button  
again, the channel is memorized again.  
1 Select “SETTING CLOCK”  
Added channel: Light blue.  
Deleted channel: Light red.  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “SETTING CLOCK”.  
Then, press the F.FWD/B button.  
5 Exit the channel setup mode  
Press the MENU button on the remote control to  
returns to TV mode.  
TIME SEARCH  
INDEX SEARCH  
NOTE: To confirm that channel(s) has been deleted  
or added, press the CHANNEL K or L button.  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
– SETTING CLOCK –  
Press the PLAY/K or STOP/L but-  
ton to point to “D.S.T.”.  
Then, press the F.FWD/B or  
REW/s button until [ON] appears.  
AUTO CLOCK  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
[AUTO]  
SELECTING THE LANGUAGE  
Make sure ...  
B
[ON]  
Press the POWER button to turn on the TV/VCR.  
NOTE: This function effects only the language on  
the screen menu and not the audio source.  
3 Exit the Daylight-Saving Time mode  
Press the MENU button on the remote control to  
return to TV mode.  
– M E N U –  
1 Select “LANGUAGE”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
Press the MENU button on the  
CHANNEL SET UP  
USER’S SET UP  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps [1] to [2], select [OFF] using the  
F.FWD/B or REW/s button.Then, press the MENU  
button on the remote control to return to TV mode.  
remote control.  
Press the PLAY/K or STOP/L but-  
V-CHIP SET UP  
B
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
ton to point to “LANGUAGE”.  
- 13 -  
EN  
9I03  
 
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
The TV/VCR’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a natural looking image.  
NOTES:  
1 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR.  
2 Select the channel number  
Press the CHANNEL K or L button to select your  
desired channel number or press the number buttons  
on the remote control.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be viewed must be selected  
on the cable box or satellite box.  
Procedures must be followed within 5 seconds or  
the Picture Control mode will be cancelled.  
When setting the Picture Control, the Game mode  
will be cancelled.  
Make sure ...  
TV/VCR power must be turned on.  
1 Select “PICTURE CONTROL”  
3 Adjust sound  
Press the VOLUME or button  
to adjust the volume.  
Press the MENU button on the  
X
Y
– M E N U –  
TIMER PROGRAMMING  
remote control.  
B
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to ”PICTURE CON-  
TROL”.  
VOLUME 20  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
C
C
C
C
C
C
C
C
C
C
C
C
Then, press the F.FWD/B button.  
GAME MODE  
2 Select item you want to adjust  
Press the PLAY/K or STOP/L button until desired  
This function enables you to decrease the TV screen  
contrast and making it suitable for use with a TV  
GAME.  
control is displayed.  
BRIGHT  
CONTRAST  
NOTE: This function can not be set during recording.  
BRIGHT  
COLOR  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
TINT  
Press the GAME button on the  
GAME  
remote control. “GAME” appears  
on the screen.  
SHARPNESS  
3 Adjust the picture control  
When you press the GAME button;  
Press the F.FWD/B or REW/s button to adjust to  
The TV/VCR comes on automatically if it is off.  
The TV/VCR will be in external input mode auto-  
your desired level.  
matically.  
REW/s  
to decrease  
brightness  
to decrease  
contrast  
F.FWD/B  
to increase  
brightness  
to increase  
contrast  
TO CANCEL THE GAME MODE  
Press the GAME button or CHANNEL K or L but-  
ton on the remote control.  
BRIGHT  
CONTRAST  
COLOR  
TINT  
SHARPNESS to soft  
to pale  
to brilliant  
DEGAUSSING  
Magnetism from nearby appliances might affect the  
color of the TV picture.  
to purple  
to green  
to clear  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect  
power cord from AC outlet then reconnect it after 30  
minutes.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
- 14 -  
EN  
9I03  
 
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button. Press the MENU but-  
ton on the remote control to return to TV mode.  
CLOSED CAPTION SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news, pre-recorded tapes with either a dia-  
logue caption or text display.  
CAPTION mode: By choosing the caption mode, you  
can watch dramas, movies and news while captioning WHEN THE CLOSED CAPTION MODE  
the dialogues and the contents of news.  
TEXT mode: By choosing the text mode, you can  
watch half screen text information if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is usually  
used for a second language if available.  
IS ON  
The On-Screen Display will disappear after 5 sec-  
onds.  
This is also true when the MUTE button is pressed,  
and when the PAUSE/STILL button is pressed  
while recording.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
NOTE:  
Not all programs are broadcast with closed captions.  
Your television is designed to provide error free  
closed captions from high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
V-CHIP SET UP  
V-CHIP enables parents to prevent their children  
Common signal conditions which may cause captions from watching inappropriate material on TV.  
errors are listed below:  
V-CHIP reads the ratings for programming (except  
for news and sports programs, unedited movies on  
premium cable channels, and Emergency Broadcast  
System signals), then denies access to programming  
if the program’s rating meets the limitations you  
select. In this case, “PROTECTED PROGRAM by  
...” message appears on the TV screen.  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter.  
Playback of poorly recorded or worn VCR tapes.  
NOTE:  
To block certain ratings, follow the steps below.  
Programming may be rated by the Motion Picture  
If the TV/VCR displays a black box on the TV  
screen, this means that the TV/VCR  
is set to the TEXT mode. To clear  
screen, select [CAPTION1], [CAP-  
TION2] or [OFF].  
Association of America (MPAA) or according to  
the Television Parental Guidelines. In order to  
block any inappropriate programming, set your  
limits in both places (MPAA RATING and TV  
RATING).  
Make sure ...  
TV/VCR power must be turned on.  
TV RATING SET UP  
Make sure ...  
– M E N U –  
1 Select “CAPTION”  
TIMER PROGRAMMING  
TV/VCR power must be turned on.  
PICTURE CONTROL  
SETTING CLOCK  
Press the MENU button on the  
CHANNEL SET UP  
USER’S SET UP  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CAPTION”.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
B
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
1 Select “V-CHIP SET UP”  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
Press the MENU button on the  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
B
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
2 Select your desired caption menu  
INDEX SEARCH  
– M E N U –  
Press the F.FWD/B or REW/s  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
button until your desired caption  
menu appears.  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
2 Select “TV RATING”  
B
– V-CHIP SET UP –  
B
TV RATING  
MPAA RATING  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “TV RATING”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
3 Exit the caption setting mode  
Press the MENU button on the remote control to  
return to TV mode.  
- 15 -  
EN  
9I03  
 
3 Select your desired item  
Press the PLAY/K or STOP/L but-  
ton to point to your desired item.  
Then, press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
(
)
)
)
)
(
MPAA RATING SET UP  
Make sure ...  
When you select the rating category and turn it  
TV/VCR power must be turned on.  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “TV-Y” to [VIEW], then all ratings  
will turn to [VIEW] automatically.  
1 Select “V-CHIP SET UP”  
Press the MENU button on the  
remote control.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Selection  
TV-Y  
TV-Y7  
TV-G  
Rating Category Explanations  
Appropriate for all children  
Appropriate for children seven and older  
General Audience  
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
TV-PG  
TV-14  
Parental Guidance suggested.  
Unsuitable for children under 14  
– V-CHIP SET UP –  
2 Select “MPAA RATING”  
TV RATING  
MPAA RATING  
B
Press the PLAY/K or STOP/L but-  
ton to point to “MPAA RATING”.  
Then, press the F.FWD/B button.  
TV-MA Mature audience only  
When you select TV-Y7, TV-PG, TV-14, or TV-MA  
and you press the F.FWD/B button, the sub-ratings  
will appear on the TV screen.  
If you select the rating category (example: TV-PG)  
and turn it [BLOCK] or [VIEW], the sub-ratings  
(example: V for Violence) will turn [BLOCK] or  
[VIEW] automatically.  
You can set the sub-ratings to [BLOCK] or [VIEW]  
individually when the rating category is set to  
[BLOCK].  
3 Select your desired item  
Press the PLAY/K or STOP/L but-  
ton to point to your desired item.  
Then, press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
G
[VIEW]  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
Selection  
G
Rating Category Explanations  
General Audience  
To set the sub-ratings individually, follow the steps  
below.  
PG  
PG-13  
R
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
When you select [TV-Y7]:  
Press the STOP/L or PLAY/K  
button to select “FV” (Fantasy  
Violence).  
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
B
NC-17  
X
Then, press the F.FWD/B button  
to select [BLOCK] or [VIEW].  
Mature audience only  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “G” to [VIEW], then all ratings  
will turn to [VIEW] automatically.  
When you select [TV-PG], [TV-  
14] or [TV-MA]:  
TV–PG  
[BLOCK]  
Press the STOP/L or PLAY/K  
button to select “D”(Suggestive  
Dialog), “L”(Coarse Language),  
“S”(Sexual Situation), or  
“V”(Violence). Then, press the  
F.FWD/B button to select  
[BLOCK] or [VIEW].  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
[VIEW]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
Note: When you select [TV-MA],  
“D” does not appear on the TV screen.  
The sub-ratings which set to [BLOCK] appears  
next to the rating category in the TV RATING  
menu.  
- 16 -  
EN  
9I03  
 
PLAYBACK  
This TV/VCR will operate with any cassette that has the  
mark. For best results, we  
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.  
INSERTING A CASSETTE  
Insert the cassette in the direction as shown. Push in  
NORMAL PLAYBACK  
gently, but continuously, on the center-back of the  
cassette until it is drawn into the TV/VCR. The  
TV/VCR will automatically turn on.  
Make sure ...  
TV/VCR power must be turned on.  
1 Insert a prerecorded tape  
If the erase-protection tab has been removed, the  
TV/VCR will start playback automatically.  
Window  
2 To begin playback  
Press the PLAY button.  
WRONG  
CORRECT  
B
PLAY  
Note: If any menu is activated on  
the screen, the PLAY button does  
not function. Press the MENU but-  
ton to clear the menu, then press the  
PLAY button.  
PRECAUTIONS  
Avoid moisture. Moisture condensation may occur  
on the tape if it is moved from a cold place to a  
warm place or visa versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your TV/VCR, wait until the tape has warmed to  
room temperature and the moisture has evaporated.  
Avoid extreme heat, high humidity and magnetic  
fields.  
3 To stop playback  
Press the STOP button when playback is completed.  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
- 17 -  
EN  
9I03  
 
AUTO REPEAT PLAYBACK  
SEARCH  
The TV/VCR has an auto repeat function that allows  
you to repeat a tape indefinitely without touching the  
PLAY button.  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
PICTURE SEARCH  
This feature is very useful in finding or skipping over  
a particular scene on a tape. In this mode, the sound  
will be muted.  
1)You may view a video tape at a high speed in  
either a forward or reverse direction by pressing  
the F.FWD or REW button during playback (in the  
SP / LP / SLP modes).  
2)Press it again and the TV/VCR will now search in  
super high speed (in the LP / SLP modes only).  
NOTE: Tapes recorded in the SP or LP mode will  
display a noise bar on the TV screen and the pic-  
ture may revert to Black and White. This is normal.  
3)Press the PLAY button to return to normal speed.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part of more than 10 seconds.  
1 Select “USER’S SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
ZERO RETURN  
This function allows you to search easily a beginning  
point that you want to review by rewinding or fast  
forwarding.  
2 Select “ALLor “BLANK”  
Press the PLAY/K or STOP/L but-  
ton to point to “REPEAT PLAY”.  
Press the F.FWD/B or REW/s  
button repeatedly until your desired  
selection [ALL] or [BLANK]  
appears.  
USER’S SET UP  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[ALL]  
[OFF]  
B
NOTE:  
Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point from which you want to review.  
3 Exit the Repeat Play setting  
Press the MENU button on the remote control to  
return to the TV mode.  
2 Reset the counter to 0:00:00  
Press the COUNTER RESET button repeatedly.  
4 Start playback  
Press the PLAY button to start the Repeat Play.  
”REPEAT PLAY B” appears.  
3 Begin recording or playback  
Press the RECORD or PLAY button.  
Press the STOP button when recording or playback is  
completed.  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the TV/VCR.  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
TO CANCEL THE REPEAT PLAY MODE  
4 To activate “ZERO RETURN” mode  
– M E N U –  
Press the MENU button on the  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “ZERO RETURN”.  
Then, press the F.FWD/B button.  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
The counter will appear on the TV screen.  
The tape will automatically stop when the counter  
returns to 0:00:00.  
- 18 -  
EN  
9I03  
 
3)Press the F.FWD/B or REW/s button to start  
index search. If you want to go forward, press the  
F.FWD/B button. If you want to go back, press  
the REW/s button.  
TIME SEARCH  
The Time Search function makes it possible to  
quickly advance the tape to your desired position  
simply by entering the exact amount of playback  
time you want to skip.  
After index search, the TV/VCR will play the tape  
automatically.  
In some cases, the index mark at the beginning of  
video tape cannot be detected.  
NOTES:  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
SLOW MOTION  
This function will not operate in recording mode.  
In the example below: To watch a program that is 2  
hours, 50 minutes from the present tape position, in  
either direction.  
Press the SLOW button to reduce the playback speed.  
The TV/VCR mutes the sound during slow motion.  
Press the PLAY button to return to normal playback.  
NOTE: If left in the Slow mode for more than five  
minutes, the TV/VCR will automatically go into the  
Stop mode.  
1 Insert a tape.  
2 Select “TIME SEARCH” mode  
Press the TIME SEARCH button (with each push it  
will increase by 10 minutes).  
RENTAL PLAYBACK  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
3 Enter your desired time  
Press the PLAY/K or STOP/L but-  
TIME SEARCH  
2 : 50  
ton until your desired time appears.  
(Example: “2:50” stands for 2  
hours 50 minutes)  
If you wish to cancel the Time Search at this point,  
press the MENU button on the remote control.  
1 Select “USER’S SET UP”  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
remote control.  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
4 Begin Time Search  
By pressing the REW/s or F.FWD/B button, the  
TV/VCR will rewind or fast forward to the specified  
point.  
The time counts down as the searching progresses.  
When 0:00 is reached, the tape will start playback  
automatically.  
USER’S SET UP  
2 Set “RENTALto [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “RENTAL”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
B
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[ON]  
[OFF]  
[OFF]  
3 Exit the Rental setting  
Press the MENU button on the remote control to  
return to the TV mode.  
TO CANCEL THE TIME SEARCH at this  
point  
Press the STOP/EJECT button on the TV/VCR or the  
remote control. This will delete the selected time.  
4 Start playback  
Press the PLAY button to start playback. “RENTAL  
PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
INDEX SEARCH  
– M E N U –  
An index signal is recorded on the  
tape automatically when the record-  
ing is started. To view a recording at  
a specific start point:  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
even after you turn off the TV/VCR.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
TO CANCEL THE RENTAL MODE  
B
INDEX SEARCH  
1)Press the MENU button on the  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
remote control. Press the PLAY/K or STOP/L but-  
ton to point to “INDEX SEARCH”, then press the  
F.FWD/B button.  
2)Press the PLAY/K or STOP/L button within 30  
seconds until the number of programs that you  
want to skip appears.  
- 19 -  
EN  
9I03  
 
VERTICAL HOLD CONTROL  
TRACKING ADJUSTMENT  
In the Pause/Still mode only, when the picture begins  
to vibrate vertically, stabilize the picture by pressing  
the CHANNEL K or L button.  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
NOTE:  
However when playing pre-recorded tapes or tapes  
recorded on units other than your own, noise lines  
(black and white streaks) may appear on the play-  
back picture. If this occurs, you can adjust the  
tracking control manually by pressing the CHAN-  
NEL K or L button until the streaks disappear. To  
return to the DTR function, stop the tape once and  
start playback again.  
You can reduce the noise lines by pressing the  
CHANNEL K or L button in slow mode, too.  
Tracking adjustment in Slow mode will not be set  
automatically.  
If there are video noise lines on the screen, see Tracking  
Adjustment section.  
STILL PICTURE  
You can view a still picture on the TV screen during  
playback (the Still mode). Press the PAUSE/STILL  
button during playback. Only tapes recorded in the  
SLP mode will show the least amount of lines. Press  
the PLAY button to return to playback.  
NOTES:  
You can advance the picture one frame at a time by  
pressing the PAUSE/STILL button during the Still  
mode.  
If it is left in the Still mode for more than five min-  
utes, the TV/VCR will automatically switch to the  
Stop mode.  
NOTE:  
In Still mode, press the SLOW button and press the  
CHANNEL K or L button until streaks disappear.  
To return to Still mode, press the PAUSE/STILL  
button again.  
RECORDING  
Make sure ...  
Before recording, make sure:  
TV/VCR power is turned on.  
The desired channel is selected by pressing the num-  
ber buttons on the remote control or the CHANNEL  
Up/Down button. (If the TV/VCR is connected to a  
cable box or satellite box, the TV/VCR must be on  
CH3 or CH4, then the channel to be recorded is  
selected on the cable box or satellite box. )  
There is a tape with its safety tab into the VCR.  
The desired recording speed is selected in SP(stan-  
dard play) or SLP(super long play) mode by press-  
ing the TAPE SPEED button on the VCR.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
NOTE: This unit will ONLY record and view the  
same channel.  
NORMAL RECORDING  
1)Begin the recording by pressing the RECORD but-  
ton.  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
T60  
1 hour  
3 hours  
T120  
T160  
To temporarily stop recording or resume it, press  
the PAUSE/STILL button. After the VCR has been  
in Pause mode for 5 minutes, it will stop automati-  
cally to protect the tape and the video head.  
NOTES:  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
ERASE PREVENTION  
You can prevent acciden-  
tal erasing of recording  
by breaking off the tab  
on the back edge of the  
cassette.  
After five minutes, the TV/VCR will automatically  
switch to the Recording mode to prevent tape  
damage.  
If “CLOSED CAPTION (ON)” is selected, the  
On-Screen Display will appear for 5 seconds, then  
disappear.  
If you decide to record  
on the tape again, cover  
the hole with plastic  
tape.  
2)Stop the recording by pressing the STOP button  
when recording is completed.  
Tab  
Plastic Tape  
- 20 -  
EN  
9I03  
 
Avoid overlap of programs ...  
There is a chance that a program will not be record-  
ed. When programs overlap:  
OTR (One Touch Recording)  
This function enables you to set the recording length  
simply by pressing the REC/OTR button on the  
VCR.  
The program with the earliest start time will record  
first.  
Once the earliest program finishes recording, the  
overlapping programs will record in the order of  
the program number.  
The illustration below demonstrates the sequence  
of recording.  
1)Begin OTR by pressing the  
OTR(2 : 30)  
REC/OTR button on the VCR  
repeatedly until the desired  
recording length appears.  
Recording stops when 0:00 is  
SP  
reached.  
Recording Sequence  
NOTES:  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
This function CANNOT be done from the remote  
control.  
9:30AM-12:00PM  
To stop the OTR operation, press the STOP button  
on the TV/VCR or on the remote control.  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
*Recording period is SHADED  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, eject the tape and turn itself off.  
1 Select “TIMER PROGRAMMING”  
Press the MENU button on the remote control.  
Push(es) Display  
Recording length  
(continuous recording)  
30 minutes  
– M E N U –  
Confirm “TIMER PROGRAM-  
MING” is pointed to by pressing  
the PLAY/K button.  
1 push  
B
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
2 pushes  
3 pushes  
4 pushes  
0:30  
1:00  
1:30  
60 minutes  
90 minutes  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
Press the F.FWD/B button.  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
If you have not yet set the clock,  
“MANUAL CLOCK SET” appears. If so, follow  
stops [3] to [8] on page 11. Then set the timer  
recording.  
17 pushes  
8:00  
480 minutes  
TIMER RECORDING  
2 Select your desired program position (1~8)  
You may set the TV/VCR to start and end a record-  
ing while you are away. You can set 8 programs to  
record on specific days, daily or weekly within a 1  
year period.  
– TIMER PROGRAMMING –  
Press the PLAY/K or STOP/L but-  
CH DATE  
BEGIN END  
ton to select the desired program  
position.  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
In the example below, the timer is being set to record:  
DATE:  
July 5th, 2002  
SETTING TIME: from 7:30PM to 8:50PM  
3 Set the channel number  
Press the PLAY/K or STOP/L but-  
ton until the desired channel num-  
ber appears.  
(Example: CH61)  
Then, press the F.FWD/B button.  
Remember:  
If your TV/VCR is connected to a cable or satellite  
box, you must set the TV/VCR to channel 3 or 4 to  
match the output channel of the box.  
CHANNEL:  
TAPE SPEED:  
CH61  
SP  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
Make sure ...  
B
If your TV/VCR is connected to a cable or satellite  
box, you must set the TV/VCR to channel 3 or 4  
to match the output channel of the box.  
Clock is set to the correct time and date before set-  
ting the timer.  
TV/VCR power is turned on to program it.  
To insert a cassette tape with its erase prevention  
tab in place. (If necessary, rewind or fast forward  
the tape to the point at which you want to begin  
recording.)  
4 Select once, every day or weekly recording  
For once recording :  
– TIMER PROGRAMMING –  
To set the channel you want to record  
Press the PLAY/K (up) button  
until the desired date appears.  
(Example: “7/05” for July 5th).  
Then, press the F.FWD/B but-  
ton.  
CH DATE  
BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/05 FRI -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
- 21 -  
EN  
9I03  
 
For every day recording : To  
record a TV program at the same  
time on the same channel every  
day. (Example: Monday through  
Sunday)  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
10 Finish setting the program  
Press the F.FWD/B or REW/s button. The program  
is now completed.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
To set another program, repeat steps [2] to [10].  
Press the MENU button on the remote control to  
Press the STOP/L (down) but-  
ton until “EVRY DAY” appears. Then, press the  
F.FWD/B button.  
return to original mode.  
11 Set the timer  
Press the POWER button to set automatic timer  
recording. The RECORD indicator lights up.  
For weekly recording : To record a TV program at  
the same time on the same channel every week.  
(Example: every Monday)  
You must turn off the TV/VCR to activate automat-  
ic timer recording.  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the STOP/L (down) button  
until “EVRY” and your desired  
day of the week appear together.  
Then, press the F.FWD/B but-  
ton.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
B
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
5 Set beginning hour  
TIMER PROGRAM EXTENSION  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “ 7, PM” for 7:30PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 FRI 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
To shift the time schedule of an automatic timer  
recording.  
1)Press the POWER button.  
2)Repeat step [1] on page 21.  
6 Set beginning minute  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
3)Press the RECORD button and select the desired  
program using the PLAY/K or STOP/L button.  
4)Press the RECORD button again.  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each additional  
push will shift forward the end time only. If you  
want to cancel while setting, press the  
PAUSE/STILL button on the remote control. The  
recording time returns to the original time.  
NOTE: When you shift forward the time schedule  
during recording, the recording speed will automati-  
cally be set to the SLP mode.  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “30” for 7:30PM)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
Then, press the F.FWD/B button.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
7 Set end hour  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “8, PM” for 8:50PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30PM - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
8 Set end minute  
5)Press the F.FWD/B or REW/s button to exit the  
setting menu. Then press the MENU button on the  
remote control to return to original mode.  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “50” for 8:50PM)  
Then, press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
TO CORRECT A PROGRAM  
While setting a program; press the REW/s but-  
ton to go back one step and enter the correct num-  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
9 Set the tape speed  
Press the PLAY/K or STOP/L but-  
ton until the desired tape speed  
appears. (Example: SP)  
bers using the PLAY/K or STOP/L button.  
After setting a program;  
1)Press the POWER button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/05 FRI 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
2)Repeat steps [1] - [2] on page 21.  
3)Press the F.FWD/B button (or press the REW/s  
button to go back one step) until the part you  
want to correct begins flashing, then make the  
changes pressing the PLAY/K or STOP/L but-  
ton.  
4)Press the POWER button to set automatic timer  
recording.  
- 22 -  
EN  
9I03  
 
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
USER’S SET UP  
2 Set “AUTO RETURN” to [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO RETURN”.  
Press the F.FWD/B or REW/s  
button until [ON] appears. Then,  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[OFF]  
[ON]  
After setting a program;  
1)Press the POWER button.  
B
2)Repeat steps [1] ~ [2] under TIMER RECORD-  
ING, page 21, and select a program you want to  
cancel.  
3)Press the T-PROG. CLEAR button.  
4)Press the MENU button on the remote control to  
return to TV mode.  
press the MENU button on the remote control to  
return to TV mode.  
3 Auto Return will begin  
When all the timer recordings are completed, the  
TV/VCR will rewind to the beginning of the recorded  
While recording is in progress;  
1)Press POWER button.  
program(s).  
NOTE:  
2)Press the STOP/EJECT button on the TV/VCR.  
If you press the POWER button while tape is  
rewinding, the Auto Return will stop.  
TO CHECK THE BEGIN/END TIME  
1)Press the POWER button so that the REC indicator  
goes off.  
2)Press the MENU button on the remote control.  
3)Confirm “TIMER PROGRAMMING” is pointed  
to.  
4 Watch the recorded program  
Press the PLAY button.  
4)Press the F.FWD/B button. The details of pro-  
grams appear on the TV screen.  
5)Press the MENU button on the remote control to  
return to TV mode.  
TO CANCEL THE AUTO RETURN  
MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button. Then, press the MENU  
button on the remote control to return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
HINTS FOR AUTOMATIC  
TIMER RECORDING  
Make sure the channel you want to record is prop-  
erly set in advance.  
WAKE UP TIMER  
The Wake Up Timer function turns on the TV/VCR  
without using the POWER button after a desired  
period of time.  
It is not necessary to press the RECORD button for  
timer recording.  
Recording begins automatically at the Start time.  
If you are recording using a Timer mode, you may  
not operate the unit manually.  
The erase-prevention tab on the cassette must be in  
place (or you must put tape over the hole).  
If the erase-prevention tab is removed, the cassette  
will be ejected when the POWER button is pressed  
to off.  
NOTES:  
Use the remote control for this procedure.  
Clock must be set to the correct time before setting  
the timer.  
If you want to select [TAPE], you must insert a  
cassette tape in the TV/VCR. The tape will start  
playback automatically on your desired time.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, and the tape will be ejected.  
1 Select “WAKE UP TIMER”  
Press the WAKE-UP/SLEEP button  
on the remote control once, and  
confirm “ON/OFF” is pointed.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
AUTO RETURN  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
WAKE UP B ON/OFF  
[ON]  
TIMER  
TV/TAPE  
TIME  
[TV]  
[12:00AM]  
– M E N U –  
1 Select “USER’S SET UP”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
Press the MENU button on the  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then, press the F.FWD/B button.  
INDEX SEARCH  
- 23 -  
EN  
9I03  
 
SLEEP TIMER  
The Sleep Timer function turns off the TV/VCR  
without using the POWER button after a desired  
period of time.  
2 Select “TV” or “TAPE”  
Press the PLAY/K or STOP/L but-  
ton until it points to “TV/TAPE”.  
Press the F.FWD/B or REW/s  
button, and select [TV] or [TAPE].  
WAKE UP  
TIMER  
ON/OFF  
B TV/TAPE  
TIME  
[ON]  
[TV]  
NOTE:  
[12:00AM]  
This function does not operate during Recording  
mode.  
3 Set wake up time  
1 Select “SLEEP TIMER”  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
Press the PLAY/K or STOP/L but-  
ton until it points to “TIME”.  
Press the F.FWD/B or REW/s  
button until your desired wake up  
time appears.  
WAKE UP  
TIMER  
ON/OFF  
TV/TAPE  
B TIME  
[ON]  
[TV]  
[12:00AM]  
2 Set sleep time  
Press the PLAY/K, STOP/L,  
F.FWD/B or REW/s button until  
your desired sleep time appears.  
Each additional push will increase (or decrease) the  
time by 10 minutes.  
SLEEP TIMER [2:00]  
Each additional push will increase  
4 Exit the Wake Up Timer setting  
Press the MENU button on the remote control to  
return to TV mode.  
the time by 30 minutes up to 120 minutes.  
Press the MENU button on the remote control to exit  
the Sleep Timer setting.  
TO CANCEL THE WAKE UP TIMER  
TO CANCEL THE SLEEP TIMER  
Press the WAKE-UP/SLEEP button on the remote  
control once, and confirm “ON/OFF” is pointed.  
Press the F.FWD/B or REW/s button until [OFF]  
appears.  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
To view the time left for sleep timer, press the  
WAKE-UP/SLEEP button twice, then press the  
MENU button on the remote control to exit the sleep  
timer setting.  
COPYING A VIDEO TAPE  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
1)Insert a pre-recorded video cassette into the Source  
(Playing) VCR or camcorder.  
2)Insert a blank video cassette, or one you want to  
record over, into the TV/VCR’s cassette compart-  
ment.  
3)Press the SPEED button on remote control for the  
TV/VCR to select the desired recording speed  
(SP/SLP).  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
Connect your TV/VCR and a Source (Playing) VCR  
using the following diagram.  
4)Press the CHANNEL K or L button on the  
TV/VCR until “AUX” appears on the screen.  
NOTE: “AUX” is found below the lowest numbered  
memorized channel. (Example: CH2)  
5)Press the RECORD button on the TV/VCR.  
6)Begin playback of the tape in the source (Playing)  
VCR or camcorder.  
[The TV/VCR]  
VIDEO AUDIO  
NOTE: For best results during copying, use the  
TV/VCR’s front panel controls whenever possible.  
The remote control might affect the source (Playing)  
VCR’s playback operation.  
[Ex: Source (playing)  
VCR or camcorder]  
Audio/Video  
adapter cable  
AUDIO  
(not supplied)  
OUT  
IN  
VIDEO  
- 24 -  
EN  
9I03  
 
ON SCREEN DISPLAY  
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote  
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:  
WHEN THE CLOSED CAPTION MODE IS OFF:  
<Off mode>  
<Counter mode>  
<Clock mode>  
Counter mode: After 5 seconds, only  
the counter remains. To clear it, press  
the DISPLAY button.  
Clock mode: After 5 seconds, only  
the clock and the channel number  
remain. To clear them, press the DIS-  
PLAY button.  
5:40PM  
CH2  
Press  
once  
Press  
once  
COUNT 0:12:34  
Press once  
OFF mode  
Clock/Counter mode  
WHEN THE CLOSED CAPTION MODE IS ON:  
The On Screen Display disappears after 5 seconds.  
STOP  
5:40 PM  
CH2  
This is true even if the MUTE button is pressed, or the  
PAUSE/STILL button is pressed while recording.  
SP  
COUNT 0:12:34  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
This shows the elapsed recording or playback time in  
When the end of a tape is reached during record-  
ing, playback, or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the TV/VCR will eject the tape and turn  
itself to off.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
hours, minutes, and seconds. (The displayed time  
will not change on a blank tape or blank portions on  
the tape.)The “–” indication will appear when the  
tape has rewound further than “0:00:00” on the tape  
counter.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
MAINTENANCE  
back, the video heads in your TV/VCR may need  
to be cleaned.  
CABINET CLEANING  
Wipe the front panel and other exterior surfaces of  
the TV/VCR with a soft cloth immersed in luke-  
warm water and wrung dry.  
1.Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
2.If a Video Head Cleaner does not solve the prob-  
lem, please call our help line at 1-800-968-3429, to  
locate an Authorized Service Center.  
NOTES:  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/VCR. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
AUTO HEAD CLEANING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
SERVICING  
Should your TV/VCR become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord, and please call our help line at 1-800-  
968-3429, to locate an Authorized Service Center.  
Playback picture may become blurred or interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use, or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
- 25 -  
EN  
9I03  
 
TROUBLESHOOTING GUIDE  
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,  
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to  
remedy the problem.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Make sure the power is turned on.  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Let the TV/VCR program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Adjust volume control on remote control or main unit.  
Press the MUTE button to restore sound.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the TV/VCR clock is set correctly.  
Make sure the tape has an erase-prevention tab. If need, cover the  
hole with plastic tape.  
No power.  
No picture and sound.  
No picture or poor picture on  
TV/VCR.  
No sound or poor sound.  
Timer recording is not possible.  
Cannot go into Record mode.  
Playback picture is partially noisy.  
Adjust tracking control for a better picture using the CHANNEL  
or L button on the TV/VCR.  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 25.  
K
No picture but the audio is OK in  
playback.  
No operation by infrared Remote  
Control.  
Video or color fades in and out  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
copy guard protection.  
when making a copy of a video tape  
.
CLOSED CAPTION PROBLEM  
My TV/VCR is showing captions  
that are misspelled.  
POSSIBLE REMEDY  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue  
in its entirety or there is a delay of are common for live broadcast. Most captioning production companies  
what is being said.  
can display a dialogue to a maximum of 220 words per minute. If a  
dialogue exceeds that rate, selective editing is used to insure that the  
captions remain up-to-date with the current TV screen dialogue.  
• Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My captions are scrambled with  
white boxes on the TV screen.  
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed  
as being closed captioned but none up the actual program so that additional advertising time can be  
of the captions were displayed.  
given. Since the decoder cannot read the compressed information,  
captions will be lost.  
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating  
show any captions. The tape box company accidentally left out the captioning signals during the  
mentions it being closed captioned. copying process.  
My TV screen shows a black box  
on certain channels.  
You are in the TEXT mode. Select CAPTION mode to CAPTION  
[OFF].  
- 26 -  
EN  
9I03  
 
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
CRT :  
13 or 19 inch in-line gun, 90˚  
deflection tube  
NTSC-M  
Video input level :  
Audio input level :  
0.5~2.0Vp-p  
-15dBs  
Television system :  
Closed caption system :§15.119/FCC  
Video S/N ratio : More than 46dB  
Audio S/N ratio : More than 43dB  
Video Heads :  
Tape width :  
Tape speed  
SP :  
LP :  
SLP :  
Tuner channel  
TV VHF Low :  
TV VHF High :  
TV UHF :  
CATV  
Rotary four-head  
1/2 inch  
OTHER SPECIFICATIONS  
[ 63134C ]  
Power requirement : AC 120V/60Hz  
Power consumption : 65W  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
Dimensions :  
H:15-3/8” (389mm)  
W:14-1/2” (367mm)  
D:14-7/8” (377mm)  
23.1 lbs (10.5kg)  
#2~#6  
#7~#13  
#14~#69  
Weight :  
[ 63194C ]  
Power requirement : AC 120V/60Hz  
Power consumption : 80W  
VHF :  
5A  
MID band :  
SUPER band :  
HYPER band :  
Terminals  
A5~A1, A~I  
J~W  
W+1~W+84  
Dimensions :  
H:19-1/2” (493mm)  
W:19-3/8” (491mm)  
D:18-3/4” (475mm)  
43.0 lbs (19.5kg)  
Weight :  
Antenna input :  
VHF/UHF 75 ohms  
unbalanced  
RCA connector [ 1  
RCA connector [ 1  
1/8” monaural (3.5 mm)  
Designs and specifications are subject to change  
without notice.  
If there is a discrepancy between languages, the  
default language will be English.  
Video input :  
Audio input :  
Earphone :  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 27 -  
EN  
9I03  
 
INDICE  
CONTROLES DE OPERACIÓN Y  
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28  
INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .31  
PREPARACIÓN DE CANALES POR  
CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31  
MODO DE ENTRADA EXTERNA . . . . . . . . . . .31 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31  
CONTROLES DE OPERACIÓN Y SUS FUNCIONES  
Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-  
tamente la misma. En este manual se muestra el modelo de 19".  
NOTA:  
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un  
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el  
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del  
mando a distancia universal.  
- PANEL DELANTERO -  
VIDEO AUDIO  
POWER  
CHANNEL  
STOP/EJECT  
REW PLAY F.FWD  
REC/OTR EARPHONE  
VOLUME  
13  
1 2 3 4 5 6 7 8 9101112  
14  
1 Toma de entrada de vídeo (VIDEO)– Conéctela a  
la toma de salida de vídeo de su videocámara u otra  
videograbadora.  
2 Toma de entrada de audio (AUDIO)– Conéctela a  
la toma de salida de audio de su equipo de audio,  
videocámara u otra videograbadora.  
3 Botón de la alimentación (POWER)– Púlselo para  
encender y apagar el televisor/videograbadora. Púlselo  
para activar la grabación con temporizador.  
4 Botones de volumen (VOLUME X / Y)– Ajustan  
el nivel del volumen.  
5 Botones de canales (CHANNEL K/ L)– Púlselos  
para seleccionar los canales deseados para ver o grabar.  
6 Ventanilla sensora del mando a distancia–  
Recibe las señales infrarrojas procedentes del mando a  
distancia.  
7 Botón de parada (STOP)– Púlselo para detener la  
cinta.  
Botón de expulsión (EJECT)–Púlselo en el modo  
de parada para expulsar la cinta del  
televisor/videograbadora.  
- CONTROL REMOTO -  
25  
26  
24  
WAKE-UP  
POWER  
/SLEEP  
EJECT  
3
CHANNEL  
RETURN  
1
4
7
2
5
8
3
6
9
15  
CHANNEL  
VOLUME  
5
4
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
23  
9
PLAY  
10  
REW  
F.FWD  
STOP  
7
RECORD  
SPEED PAUSE/STILL  
22  
21  
11  
18  
T-PROG.  
CLEAR  
GAME  
SLOW  
COUNTER  
RESET  
19  
20  
Botón L–  
Púlselo para seleccionar los modos de ajuste desde el  
menúde la pantalla.  
Púlselo para introducir dígitos cuando establezca un  
programa.  
(Por ejemplo: Para ajustar el reloj o establecer un pro-  
grama de temporizador)  
- 28 -  
ES  
0I29  
 
- PANEL TRASERO -  
ANT.  
27  
28  
minimizar el ruido de vídeo (líneas o puntos en la pan  
talla) durante la reproducción.  
8 Botón de rebobinado (REW)– Púlselo para  
rebobinar la cinta, o para ver la imagen en retroceso  
rápido durante el modo de reproducción. (Búsqueda  
con rebobinado)  
14 Compartimiento del videocasete  
15 Botones numerados– Púlselos para seleccionar los  
canales deseados para ver o grabar. Para seleccionar  
canales del 1 al 9, pulse primero el botón 0 y luego el  
botón 1 a 9.  
Botón s–  
Púlselo para seleccionar un modo desde un menúpar-  
ticular.  
Botón +100– Cuando seleccione canales de tele-  
visión por cable cuyo número sea superior al 99, pulse  
primero este botón, y luego pulse los dos últimos dígi-  
tos. (Para seleccionar el canal 125, pulse primero el  
botón “+100” y luego el “2” y el “5”.)  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
9 Botón de reproducción (PLAY)– Púlselo para ini-  
ciar la reproducción.  
Botón K–  
Púlselo para seleccionar los modos de ajuste desde el  
menúde la pantalla.  
Púlselo para introducir dígitos cuando establezca un  
programa.  
(Por ejemplo: Para ajustar el reloj o establecer un pro-  
grama de temporizador)  
16 Botón de menú (MENU)– Púlselo para visualizar el  
menúprincipal en la pantalla del televisor.  
17 Botón del visualizador (DISPLAY)– Visualiza el  
contador o el número del canal actual y la hora actual  
en la pantalla del televisor.  
18 Botón de velocidad de cinta (SPEED)– Púlselo  
10 Botón de avance rápido (F.FWD)– Púlselo para  
avanzar rápidamente la cinta, o para ver la imagen en  
avance rápido durante el modo de reproducción.  
(Búsqueda con avance rápido)  
para elegir la velocidad de grabación deseada: SP/SLP.  
19 Botón T-PROG. CLEAR– Púlselo para cancelar un  
programa de temporizador.  
Botón de reposición del contador (COUNTER  
RESET)– Púlselo para reponer el contador a 0:00:00.  
Botón B–  
Cuando establezca un programa (por ejemplo: para  
ajustar el reloj o para establecer un programa de tem-  
porizador), púlselo para determinar su elección y vaya  
al paso siguiente que quiera introducir.  
Púlselo para determinar los modos de ajuste desde el  
menúde la pantalla.  
Púlselo para seleccionar un modo desde un menúpar-  
ticular.  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
20 Botón de juego (GAME)– Establece el modo del  
juego y el modo de entrada externa al mismo tiempo.  
21 Botón de cámera lenta (SLOW)– Pulselo para  
activar la reproducción a cámera lenta.  
22 Botón de pausa/imagen fija (PAUSE/STILL)–  
Púlselo para detener temporalmente la cinta durante la  
grabación o para ver una imagen fija durante la repro-  
ducción.  
23 Botón de silenciamiento (MUTE)– Silencia el  
11 Botón de grabación (REC)– Púlselo para iniciar la  
sonido. Púlselo de nuevo para recuperar el sonido.  
grabación manual.  
24 Botón de retorno de canal (CHANNEL  
RETURN)– Púlselo para volver al canal anterior. Por  
ejemplo, pulsando una vez este botón, la visualización  
del canal cambiará de 3 (canal actual) a 10 (canal ante-  
rior), y al pulsarlo por segunda vez, el canal cambiará  
del 10 al 3.  
25 Botón del temporizador despertador/para  
dormir (WAKE-UP/SLEEP)– Ajusta el tempo-  
rizador para despertarse/dormir.  
Botón de grabación de un toque (OTR)– Activa  
la grabación de un toque. (Sólo en el  
televisor/videograbadora)  
12 Indicador de grabación (RECORD)– Parpadea  
durante la grabación.  
Se enciende en el modo de espera de la grabación con  
temporizador.  
13 Toma de auriculares (EARPHONE)– Para conec-  
tar los auriculares (no suministrados) y escuchar en  
privado. La toma es mono y tiene un tamaño de 3,5  
mm.  
26 Botón de expulsión (EJECT)–Púlselo en el modo  
de parada para expulsar la cinta del  
televisor/videograbadora.  
Se puede mostrar el menú principal en la pantalla del  
televisor pulsando repetidamente este botón del televi-  
sor/videograbadora.  
27 Cordón de alimentación– Conéctelo a la toma de  
CA estándar (120V/60Hz).  
28 Terminal de antena (ANT.)– Para conectar una  
Función de seguimiento– Pulse los botones para  
antena o sistema de televisión por cable.  
- 29 -  
ES  
0I29  
 
CONEXIONES DE ANTENA/CABLE  
Desde el cable coaxial o  
caja de emisiones vía  
satélite de 75 ohm del  
sistema de Cable  
Caja de CATV  
o caja de emi-  
siones vía satélite  
(no incluído)  
Antena combinada de  
VHF/UHF  
(no incluído)  
Antena de varilla UHF/VHF  
(incluído para solamente 13”)  
OUT  
IN  
Antena VHF  
(no incluído)  
Desde el  
sistema de Cable  
Antena UHF  
(no incluído)  
o
Combinador de  
o
VHF/UHF  
(no incluído)  
ANT.  
Cable coaxial  
de 75 ohm (no incluído)  
o
o
CABLE CON CONVERTIDOR/DESCODIFICADOR  
O CONVERTIDOR DE EMISIONES VÍA SATÉLITE  
Si su servicio de televisión por cable le suministra un con-  
vertidor, o si usted utiliza un sistema de emisiones vía  
satélite, usted podrá utilizar las conexiones básicas.  
Utilizando estas conexiones, usted también podrá grabar  
canales codificados. Sin embargo, la selección de los  
canales deberá hacerse con el convertidor de televisión por  
cable con el convertidor de emisiones vía satélite. Esto sig-  
nifica que los canales no podrán ser cambiados con el  
mando a distancia del televisor/videograbadora. La  
grabación inatendida se limita a un canal cada vez.  
ANTENA COMBINADA DE VHF/UHF  
La antena de varilla de VHF/UHF (incluído para solamente  
13”) es desmontable. Inserte el vástago de la antena en el  
agujero de la parte trasera superior del  
televisor/videograbadora.  
Conecte la varilla de antena de VHF/UHF o la antena com-  
binada de VHF/UHF al terminal ANT. del  
televisor/videograbadora.  
ANTENAS SEPARADAS DE VHF/UHF  
En algunos lugares será necesario utilizar una antena exte-  
rior.  
PARA GRABAR UN CANAL  
CODIFICADO/DESCODIFICADO  
CABLE SIN CONVERTIDOR/DESCODIFICADOR  
1. Ajuste el selector de canales del televisor/videograbado-  
ra al canal de salida del convertidor de televisión por  
cable o del convertidor de emisiones vía satélite. (Ej.:  
CA3)  
2. Seleccione el canal que desee grabar de su convertidor  
de televisión por cable o del convertidor de emisiones  
vía satélite.  
Utilice esta conexión si su sistema de televisión por cable  
se conecta directamente a su televisor/videograbadora sin  
convertidor.Utilizando esta conexión usted podrá:  
1)Utilizar el mando a distancia del televisor/videograbado-  
ra para seleccionar canales.  
2)Programar uno o más canales sin codificar para realizar  
la grabación automática con temporizador.  
NOTA: Con esta unidad SÓLO se podrá grabar y ver un  
mismo canal al mismo tiempo.  
- 30 -  
ES  
0I29  
 
MODO DE ENTRADA EXTERNA  
AJUSTE DEL RELOJ  
Cerciórese...  
Cuando utilice una señal de entrada externa (otra  
videograbadora o una videocámara), conecte los cables de  
salida de audio/vídeo del equipo de reproducción a las  
tomas AUDIO IN/VIDEO IN de su  
televisor/videograbadora. Y luego pulse el botón CHAN-  
NEL K o L hasta que “AUX” aparezca en la pantalla.  
La alimentación del televisor/videograbadora deberá  
estar conectada.  
En el ejemplo de abajo, el reloj va a ajustarse así:  
FECHA: 7 de mayo de 2002  
HORA: 5:40 PM  
1) Pulse el botón MENU en el mando a distancia.  
Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE RELOJ”.  
Usted puede programar el temporizador para que explore  
todos los canales que puedan recibirse en su zona.  
Luego, pulse el botón F.FWD/B.  
INSTALACIÓN DE LAS PILAS  
2) Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE MANUAL RELOJ”.  
1)Abra la tapa del compartimiento de las pilas del mando  
a distancia presionándola en el sentido de la flecha.  
2)Inserte 2 pilas tamaño “AA” en el compartimiento de las  
pilas, en el sentido indicado por las marcas de polaridad  
(+/-).  
Luego, pulse el botón F.FWD/B.  
3) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el mes deseado. (Ejemplo: Mayo - 05)  
Luego, pulse el botón F.FWD/B.  
4) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el día del mes deseado. (Ejemplo: 7 - 07)  
3)Vuelva a poner la tapa.  
Luego, pulse el botón F.FWD/B.  
5) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el año deseado. (Ejemplo: 2002)  
Luego, pulse el botón F.FWD/B.  
6) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
la hora deseada. (Ejemplo: 5, PM)  
Luego, pulse el botón F.FWD/B.  
7) Pulse el botón PLAY/K o STOP/L hasta que aparezca  
el minuto deseado. (Ejemplo: 40)  
PREPARACIÓN DE CANALES POR  
PRIMERA VEZ  
8) Pulse el botón MENU en el mando a distancia. Aunque  
los segundos no se visualizan, éstos empiezan a contar  
desde 00 cuando se pulsa MENU en el mando a distan-  
cia. Utilice esta función para sincronizar el reloj con la  
hora correcta.  
1) Enchufe el cable de alimentación del  
televisor/videograbadora en una toma de CA estándar.  
NOTA: Si aparezcan algunos digitos en el rincón de la  
pantalla, pulse el botón POWER sin desenchufar el cable  
de alimentación.  
2) Pulse el botón POWER para encender el  
televisor/videograbadora.  
3) Seleccione “ENGLISH” o “ESPAÑOL” utilizando el  
botón F.FWD/B o REW/s. “[ ]” indica el idioma  
seleccionado.  
4) Pulse el botón PLAY/K o STOP/L para señalar  
“AUTOPRESELECCION”.  
Luego pulse el botón F.FWD/B. El sintonizador explo-  
rará y memorizará todos los canales activos de su área.  
NOTAS:  
El televisor/videograbadora distingue entre los canales  
de televisión estándar y los canales de televisor por  
cable.  
Si desea reproducir o grabar una cinta ANTES de prea-  
justar el sintonizador, usted tendrá que pulsar el botón  
MENU en el mando a distancia. Para preajustar de  
nuevo el sintonizador, consulte “REPETICIÓN DE LA  
PREPARACIÓN DE CANALES”.  
La unidad de televisor/videograbadora puede reconocer  
los canales de TV como ellos de TV por cable a causa  
de los condiciones de recepción. En este caso, pruebe el  
preajuste automático de nuevo en los condiciones finas  
de recepción.  
5) El sintonizador se para en el canal memorizado más  
bajo. Si desea recuperar canales seleccionados, usted  
podrá seleccionar directamente el canal deseado con los  
botones numerados del mando a distancia o con los  
botones CHANNEL K o L.  
- 31 -  
ES  
 
LIMITED WARRANTY  
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials  
or workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from  
the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded  
from this warranty.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date  
of original retail purchase.  
LIMITS AND EXCLUSIONS:  
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail  
purchase will be required together with the product to obtain service under this warranty.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty  
does not apply to any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product  
not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplica-  
tion, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FIT-  
NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTA-  
TIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED  
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS TAKEN TO A FUNAI AUTHO-  
RIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT  
FUNAI CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITH-  
OUT PRIOR NOTICE.  
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,  
please call 1-800-968-3429 or write to the following:  
FUNAI CORPORATION, INC.  
Customer Service  
100 North Street; Teterboro, NJ 07608  
Tel :1-800-968-3429  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in Malaysia  
0EMN01975  
T5314 / 7314UQ * * * * *  
 

Sony CRT Television KV SW21M81 User Manual
Sony GPS Receiver NV U53 User Manual
Sony VCR 2000 PRO User Manual
Spectra Mouse KT4092 User Manual
Star Manufacturing Griddle 0106 User Manual
Stiga Lawn Mower 13 6185 14 User Manual
Sungale Tablet ID1019WTA User Manual
Sylvania TV VCR Combo SRC21135 User Manual
Symphonic TV VCR Combo MGTD204 User Manual
Tanaka Brush Cutter TBC 325 User Manual