Sony Network Card CARRIERGATE User Manual

4-680-222-11(1)  
4 Can the IP address of the computer be acquired?  
With the computer setting “Obtain an IP address automatically” enabled, perform the following  
steps. For information on how to set the IP address of the computer, see Windows Help.  
Preparations  
Connections  
Windows Me operating system  
Case 1 No communication between the computer and  
Wireless Broadband Router  
Case 1 Cannot display the Setup Page (an error message  
appears)  
Click “Start”, and click “Run”.  
1
2
1 Are you attempting to establish a connection at a frequency  
check the following.  
In the dialog box used to specify the file name, enter “winipcfg” (exclude the  
of 5 GHz?  
quotation marks) and click “OK”.  
Wireless  
Broadband Router  
The default wireless broadband frequency setting is 2.4 GHz. If you want to establish a wireless  
connection at 5 GHz, access the Access Point Setup page through a wired network, and change  
the frequency setting to 5 GHz (802.11a). Refer to the separate Quick Start Guide for details about  
how to display the Access Point Setup page.  
1 Can the IP address of the computer be acquired?  
See “Preparations”, “Case 1: No communication between the computer and Wireless Broadband  
Router”, item 4.  
2 Was your computer properly configured for wireless  
2 Are the Access Point and Router Unit power connections  
communication?  
Troubleshooting Guide  
This document provides solutions to common problems  
encountered with the Wireless Broadband Router.  
correct?  
When using the Access Point functions under factory default settings, configure the computer as  
follows.  
When powered properly, the Status indicator of the Router Unit is lit and the Status indicator of  
the Access Point is flashing slowly.  
From the list in the “IP Setup” dialog box, select the Wireless LAN interface that you  
are using (PC card, computer internal wireless LAN, etc.).  
3
The factory default settings of the Access Point function are:  
• Network Name (SSID):  
The 6-character identifier printed on the label inside the rear cover of the Wireless Unit  
3 Is the AC adapter power switch on?  
Make sure that an IP address is shown in the “IP address” text box.  
4
5
Please refer to this guide before contacting Sony  
Customer Information Services.  
Make sure that the AC adapter is properly connected and verify that the power switch is on.  
z Hint  
If the IP address is “0.0.0.0” or an address starting with “169.254.” is displayed, click  
“Release”, and then “Renew”.  
z Hint  
For details about the location of the network name (SSID), refer to procedure 3 of the Quick Start Guide.  
When the AC adapter power switch is on, the LED on the adapter is lit.  
• Security settings  
Encryption (WEP): Disabled  
• IEEE 802.11 Mode: 11g, 11b (High multicast rate)  
The PCWA-AR800 consists of:  
• Broadband Router Unit  
PCWA-R1  
• Wireless LAN Access Point  
PCWA-A820  
With the Windows Me and Windows 2000 operating systems, perform setup as described in the  
documentation provided with your Wireless LAN PC Card.  
With the Windows XP operating system, proceed as follows.  
In this document, we refer to the Broadband Router Unit as the  
Router Unit and to the Wireless LAN Access Point as the Access  
Point.  
Power switch  
a: Off  
? : On  
The PCWA-AR800 can be used at frequency settings of 2.4 GHz  
and 5 GHz. Change this setting as necessary. (By default, the  
PCWA-AR800 is set to 2.4 GHz.)  
Click “Start”, and then click “Control Panel”.  
1
2
To power outlet  
In “Control Panel”, click “Network and Internet Connections”, and then click  
“Network Connections”.  
LED  
Note  
z Hint  
If an IP address starting with “169.254.” is displayed, a suitable IP address was not obtained with  
“Obtain an IP address automatically” and your Windows operating system assigned an address to the  
wireless LAN PC card or Wireless LAN Converter. In this condition, correct network connection is not  
possible. Perform the setup again as described in the separate Quick Start Guide.  
If “Network and Internet Connections” does not appear, click “Switch to Category View” on the left.  
In the “Network Connections” window, right-click the icon of the wireless network to  
Cable modem or DSL modem  
3
which you want to connect, and click “View Available Wireless Networks”.  
PCWA-AR800  
Windows 2000 and Windows XP operating systems  
4 Is the Ethernet cable correctly connected?  
©2004 Sony Corporation Printed in Japan  
Make sure that an end of the Ethernet cable is connected to a LAN connector of the Router Unit.  
Connect the other end of the Ethernet cable to your computer.  
Click “Start”, point to “Programs” (“All Programs” when using the Windows XP  
operating system) and then “Accessories”, and click “Command Prompt”.  
1
z Hint  
The Ethernet port of your computer is on its back panel.  
In the command prompt window, enter “ipconfig /all” (exclude the quotation marks)  
and press the Enter key.  
2
5 Is the Windows XP “Internet Connection Firewall” function  
Contents  
Verify the IP address setting information of the Wireless LAN interface that you are  
using (PC card, computer internal wireless LAN, etc.).  
3
enabled?  
Preparations  
If the “Internet Connection Firewall” function is enabled, communication may not be possible.  
See “Miscellaneous”, “Case 4: Computer firewall function and browser proxy settings” for details.  
• No communication between the computer and  
Wireless Broadband Router ........................................................................ Case 1  
6 Is the Web browser of the computer used for the Wireless  
Connections  
Broadband Router setup configured to use a proxy server?  
Make sure that there are no proxy settings enabled for the IP address of the Wireless Broadband  
Router. See “Miscellaneous”, “Case 4: Computer firewall function and browser proxy settings”  
for details.  
In the “Connect to Wireless Network” dialog box (with Windows XP SP1, the  
4
• Cannot display the Setup Page (an error message appears) ..................... Case 1  
“Wireless Network Connection” dialog box), select the Access Point from “Available  
Wireless Networks”, and click “Connect”. (When using the Access Point functions  
under factory default settings, check the 6-character identifier printed on the label  
inside the rear cover of the Wireless Unit.)  
Router Functions  
• The Internet Gateway is shown as a network connection.  
What does this mean? ................................................................................ Case 1  
3 Are the network name (SSID) and security settings configured  
• Cannot connect to the Internet.................................................................... Case 2  
correctly?  
• I changed the LAN settings of the Router Unit, but I can no longer  
connect to the Router Unit or network ........................................................ Case 3  
z Hint  
To connect to the Access Point, the network name (SSID) and security settings must be the same  
at the computer and the Access Point.  
The “Description” field shows the name of the Wireless LAN interface.  
Access Point Functions  
If the IP address is “0.0.0.0” or an address starting with “169.254.” is displayed,  
enter “ipconfig /renew” (exclude the quotation marks) and press the Enter key.  
A new IP address is assigned.  
z Hint  
4
• Clicked the “Refresh” button under “Access Point List”, but nothing  
appears in the list ........................................................................................ Case 1  
When using the Access Point functions under factory default settings, use the settings listed in 2 above.  
With the Windows Me and Windows 2000 operating systems, verify the Access Point network name (SSID)  
and security settings of the wireless LAN PC card as described in its documentation.  
• Several Access Points are listed, but I do not know which one to select.... Case 2  
Note  
With the Windows XP operating system, proceed as follows to verify the settings.  
• The user name and password input dialog box appears despite  
the lack of settings ...................................................................................... Case 3  
If an IP address starting with “169.254.” is displayed, a suitable IP address was not obtained with  
“Obtain an IP address automatically” and your Windows operating system assigned an address to the  
wireless LAN PC card or Wireless LAN Converter. In this condition, correct network connection is not  
possible. Perform the setup again as described in the separate Quick Start Guide.  
Open the “Connect to Wireless Network” dialog box (with Windows XP SP1, the  
“Wireless Network connecion” dialog box) as described in 2 above.  
1
• Unable to connect after Access Point functions settings are made ............ Case 4  
• If “Easy Setup” is used after “Advanced Setup”,  
what about items not included in “Easy Setup”? ......................................... Case 5  
Select the network name (SSID) of the Access Point from “Available Wireless  
Networks”.  
2
Miscellaneous  
Make sure that the security settings of the Access Point match those of the  
computer.  
3
• Forgot settings ............................................................................................ Case 1  
• The power cord is plugged to the AC outlet, but the indicators  
• Sony, VAIO,  
,
, and the Eco Info logo are trademarks of Sony Corporation.  
do not light .................................................................................................. Case 2  
Click “Connect”.  
4
• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other  
countries.  
• After pressing the Quick Setup switch, the Status indicator  
starts flashing red........................................................................................ Case 3  
If the connection is not established, reset the Access Point functions to the factory default  
settings as described in “Miscellaneous”, “Case 1: Forgot settings”, and then set up the  
Access Point functions again as described in the separate Quick Start Guide.  
• In this document, Microsoft® Windows® Millennium Edition is referred to as Windows Me, Microsoft® Windows®  
2000 Professional is referred to as Windows 2000, Microsoft® Windows® XP Home Edition and Microsoft®  
Windows® XP Professional are referred to as Windows XP.  
• Computer firewall function and browser proxy settings .............................. Case 4  
• Netscape is a registered trademark of Netscape Communications Corporation.  
• All other names of systems, products and services are trademarks of their respective owners.  
• In the document, the ™ or ® marks are not specified.  
Printed on 100% recycled paper using VOC (Volatile Organic Compound)-free vegetable oil  
based ink.  
Continued on next page  
 

Smooth Fitness Treadmill 515P User Manual
Sony Camera Lens SAL70200G2 User Manual
Sony Home Theater Server HT XT1 User Manual
Sony Home Theater System DAV DZ531W User Manual
Southern Telecom MP3 Player SMP517 4 User Manual
Speed Queen Dishwasher SDET07 SDGT09 User Manual
Stanton Turntable STR8 30 User Manual
Sunbeam Juicer JS7300 User Manual
SVAT Electronics Digital Camera GX5201 User Manual
Sylvania MP3 Player SMPK6958 User Manual